The latency of RAM for ryzen 2600
Now lateinos 76ns , this is normal performance or not ?Spoiler
Men who understand, please tell the newcomer. Gathered a new system and for the first time decided to raise the frequency of RAM. As a result, from 2666 raised to 3200 without raising the voltage.
Tell me these are normal results? And how to check for stability?
Apti
Spoiler https://forums.overclockers.com.au/viewtopic.php?f?4't'578879's sid'8a56f7e3e95519df7a7a72c1a07304
You have to look at sa/io for fun, there are boards that inadequately inflate them, so you can't put in xmp. I've got 3600, MSI at 1.3/1.3.
Apti wrote:
Tell me these are normal results?
Latensey a lot, we need to reduce.
Apti wrote:
And how to check for stability?
TM5, if only the memory test, if the whole system, then advise Prime95, the last klinsc (they I tested the whole system in acceleration, tsd memory), but, imho it's too much. Lynx yuss only with a well-organized cooling of the body, coolers, etc., because the system roasts decently, but quickly.
Apti
AIDA64 and https://drive.google.com/drive/folders/17u_88vsjraTDw5_wI6gJY05peEicbBsQ
Enough for a stability test.
If the OME 's" bars (without radiators) can stop.
If there are radiators, then look through Typhoon Burner http://www.softnology.biz/
What chips and you can twist the acceleration further, suddenly 4000 mtsy will go. There will be a noticeable increase in the games.
Here's a https://club.dns-shop.ru/hardware/kompleksnoe-testirovanie-modulej-operativnoj-pamyati-ddr-4-sdram/ for help
Ryazancev
Thanks for the response
Yes, I am not chasing the acceleration, I would know that these results are adequate and stable and I would stop there.
Is it true that I have a high latency rate?
Apti
For your settings, normal Latini, typical. If you need to do better, you should at least spin 2 sub-minimumings (most of all bust). tREFI (65535 chewingly) tRFC (300 desirable), but this may require a voltage boost.
Ryazancev
Thank you for the answers))
If I'm fine, I'd rather not go anywhere else with my crooked hands xD
Apti
Apti wrote:
And how to check for stability?
FallOut 4 run.It is sensitive to acceleration.What Aida64 will miss, then Fall4 can not miss (may be departures without errors, or hanging)
Denis Kyokushin
If I was on the computer, I would run with high, but to pump so much GB as a benchmark ... )
Denis Kyokushin
in truth, except for a pair of aida-like binches, furmark and msi afterbernera with cpu z nothing)))
Toys have not yet had time to put
Witch 3 think to put here
Hello everyone, I've updated the computer here and faced with the problem of "Latency" , and I began to try to drive the operative, lower the timing and raise, the frequencies more than 3 to for some reason does not take but it is not surprising (the same deshman operation).
Rarity96
Well, at 3000MHz RAM, what's the latency?
Have you tried 3200 or 3133?
The author of Thaiphoon Burner notable Russophobe, blocked the launch of proga on the Russian wind...
Joni228
Yes, I often changed these timings. Now, in my opinion, 16-16-16-36. The latency is high, over 70 ns. And I lowered the frequency to 3000 MHz, the computer began to go blue. I raised v soc to 1.188- 1.200v. Outside of RAM 1.39v
I tried it like this, according to the calculator:
Spoiler 
Bios flew to the previous version