ASUS R9 280x DirectCU II TOP problem

DartMaul
If the addition of the voltages and update the BIOS of the video card does not help, then I don't even know what to do :)

MisterMIKL
What you wrestle with Furemark drive - if the video card prohetic test without errors and artifacts - so the problem is software/drivers/conflicts with the need... and if not - feel free to carry in SC or back to the store if there is a guarantee.

danene
In FurMark, no artifacts, 20 minute test conducted.

Here's a test

Furmark frankly not the best test to check for errors (I use OCCP but right now is not about that)
Load vdroop to 1.12 v. This may be a problem.

DartMaul
Good, but is it possible to fix?
If you raise the voltage, then tell me how?)

Using a program to overclock the cards of course.
MSI Afterburner or Asus'ovsky GPU Tweak. Actually, Afterburner is considered the best and most convenient, but if there are some special perks and DC2 they will be available only via GPU Tweak

DartMaul
Opened MSI Afterburner and see here is, as I understand it should be 1200

P. S: Core Voltage (mV) 1144 instead of 1200, and the ASUS GPU Tweak GPU Voltage (mV) 1200

the picture is not loaded:(

MisterMIKL
Core Voltage (mV) 1200 1144 instead
It is in the monitor or in the settings?

DartMaul
In the settings

Try to put 1.2 v through AB and run furmark, will look much the actual voltage on the GPU.

DartMaul
Nothing has changed, in the BIOS is blocked?

DartMaul This is a great test to check for artifacts, quality and overclocking (if any), if not the best, it loads all the conveyors/the memory, and if there were problems with overheating GP/ Memory test would have been in the 10th minute krasilka sypya artifacts. So the problem must be sought elsewhere, I'm sure at 99% and I understand that the artifacts are only in battle 4?
MisterMIKL
Core Voltage (mV) 1200 1144 instead
Plays no role, the error of the voltage sensor card.

danene
He didn't ship the memory and not checking for errors.

If in the settings of the 2 programs show different values, it is not the accuracy of the sensor (in fact this may not be the error of the sensor as the sensor is one and whatever he said he said the same thing both programs), is a software bug. So it is necessary to raise the voltage a little higher, you can start from 1.21 v.

DartMaul
This is the error tembolee different programs remove the data according to various algorithms, All programs which are based on Riva Tuner will show the same data, but assume softina written by ASUS will show other data (+/-), respectively, if the ASUS card is known to be accurate readings will be in the program written by the producer.
And about the RAM - if I remember correctly in Furmark'e have changed the plugin VMT (Video Memory stress Test) but if to speak in essence I had the same problem with the 780 ti, with 20-30 minutes of the game started artifacty shadows on stretches of the road, and textures at a great distance (which is, in principle, often), then over time, friezes, drove formaram - the base of the bagel flickered, began to wrestle with it, took it to SP I master in 15 minutes, said that problems with memory (which is not typical for 780), too sinned on overheating, but it turns out the problem appeared as you fill VRAM....

danene
Artifacts popping up only in BF 4 and it happens that the round you can play without them, look in GPU Tweak there is a GAMING mode ,you can try to turn it on.

P. S: I would have long changed to gtx 770, but as SC said the defect is not detected

All kind of buggy r9 280x line cards or I have something wrong . The BIOS of the video card you can upgrade (there is a fix for artifacts)

Well update.
This is the way I think is done via GPU Tweak.

DartMaul
Probably a silly question, the warranty is not flies?