The gear lever
Hello to all motorists and europrofessional! I want to share another farm. Rather Audiogasm! So, I had to slide the handle out of metal. In the summer heat, and in winter it was possible for her to freeze! Had to wear the glove until hot. The situation is not a stalemate, but we're looking for is not the easy way out. Due to the fact that I'm a musician, I wanted somehow to play this. Add personality! "Dug into the old microphones"...Found! And thoughts fly! Just wanted just put a MIC and all, and then "the Appetite comes while eating"! Glowing microphone seemed nice eye candy. Then the backlight of stuff in the pocket and a bright spot in a gray day! And I want to — it's worse than pain! Anyway, I picked up the right nut and began to try on! With MIC produced a real "act of vandalism"! The whole inside had to, brazenly, to throw out. It was decided to pour epoxy resin. The mesh heads are covered with sealant that the epoxy does not leak. The nut was wound on a wooden stick, pre-lubricated with petroleum jelly. Honestly speaking with the electrician I am acquainted in absentia, so I had to drive brother! It pissed off. And ribbon he was...diode Diodes 12 volt can be cut in 3 pieces — it is just slightly more than the circumference of my wooden sticks! Between the nut and the tape as a reflector put a wide washer. Was fixed ottsentrovano it's all in the head and filled epoxy! I powered up from the rear ashtray, altered sekerak. I do not smoke and do not like when in the car Smoking!
I apologize for the camera phone pictures!
Thank you.I will split hairs.There are a couple of ideas that can upgrade your design.
I filled in everything completely, and the upper and lower bracket. Did so for greater strength. All plastic, if you pull may go wrong! (still have reverse gear!). The nut is completely in the resin — it holds everything! And the handle just covers leather casing. The switch does not fit because of the diameter of the handle — where he is himself and nobody bothers, but when you start to put it on the lever...and then had to clean it up. Can button to make it somewhere! The very epoxy under the net (the upper part), so not so much light, I think to paint with spray in black (a mesh then wipe that silver left).Although at night I travel often, and it is getting dark later now.
In thanks for the detailed answer.Got almost all the answers.Will do slowly, but the native knoper want to keep.I have buttons all the wiring laid inside the handle in the tunnel and therefore the wiring is already there, just podatsa to power.Instead of a cap use native coil microphone, she's just a groove under sveiki.I'm just not sure whether to fill epoksidnoj upper grid or to leave it at that, but then maybe bright will be highly-?What do you big fat liar? What do you say?
Sorry pictures of the whole process, no! Now I will try a little more detail! The pen unscrewed from the mesh of the microphone — that's it, cut out of cardboard two rings (outer diameter — inner diameter of the handle, and the inner — diameter sticks).Thus was attentional! Now stick in the rings, it is necessary to set the depth of "occurrence" nuts and fireflies in the mesh of the microphone(above or below). The wand, of course greased "grease". The LEDs are glued around the sticks on a suitable tube (with cans of silicone unscrewed the "nose" — clearly came), the circumference of the tube is the length of three LEDs with tape! Patpal, heat shrink to put on, all don't forget! Gathered all not a stick — on fire! Filled epoxy mesh head and boiled it with the stand assembled! Switch wanted to put my own microphone, there is not enough space. Nothing complicated! Go for it! Don't forget to post photos when you're done!
I liked the joke.I'd have a button operated to turn off power or sometimes even in parallel with the toad reverse.Explain how to Centraal and filled nuts, wand prikleilsya on forever or it should be like that grease-? Give details, and then found the microphone, already itching to start to split hairs.
budikshur
Quote from you in relation to your same comments: "I sincerely believe that most of you knows better what I need and why I was wrong making this choice, but I somehow FSUs on it."
envy is a bad thing. he can't hands but language can)) Muti on krasava!
quote, the word verification quote. Characteristically, illiterate people from the city usually try to make candy, but forget one rule : how many g of sugar are not posipal on the jam still does not seem to become. And Yes, success to you.
Quote from you in relation to your same comments: "I sincerely believe that most of you knows better what I need and why I was wrong making this choice, but I somehow FSUs on it."
Like crazy — so directly and immediately. What machine you got the throat immediately, perhaps from an inferiority complex ?
Well, I hope it will, and the result will be attackan ;-) =)
And so, Yes, the idea is interesting. Moreover, I'm also no stranger to microphones.
One of my favorite topics about machines and microphones — it is a dialogue of the Blues Brothers:
— Where our blyuzmobil? You sold our blyuzmobil? How could you?
— I'm not sold. I had it changed.
— What?
— On MIC.
Good?
Yes.
— Well, OK.
Yes, the mesh is sitting there in the epoxy is hard! I why want to "spray"?! The very resin in black color and the mesh while wet paint dry. Well, that should be (of type) get the gray mesh, the dome is black! Well, or it will not work! Anyway, thanks for the interest in my farm!
If dimming, then do not spray. Honestly, I would advise to cut out a circle of tin and beat with a hammer (using the ball from the big bearing, for example), would be part of the sphere, which could be put inside the MIC, if it still spins... But I guess he already completely filled with epoxy, which is not removed but drill it (not all, only part that you have to close the tin) just too lazy... And spray the cool part — he stripped off pretty quickly. These paints are not resistant to constant physical contact.
By the way, looked. On my farm is worth the label "R-1". Don't know what that means, but such labels already saw somewhere in Vomero and nines cross-tuning =)
Thank you for the constructive criticism! At night or in the evening ride a little, however, largely your truth! Lighting should not distract! Initially, the idea was to make a slight glow in the lower part of the head of the microphone, but it turned out that glows all!:( I'll try to toned the upper part of the spray is to do as intended!
I have some farm from the previous owner. There is also flashing in three modes didici. Not very bright, but a lot. Button top =( I stupidity took apart and looked why does not burn. It turned out, the batteries are not. Well, I, umnaya Masha, I bought a battery and stuck. I had exactly a week, while looking for the cause of missing the pleasure of driving. When found thrown out nafig battery.
I like to ride in the evening and night. So this extra light is strongly prevents to live to me personally. Love to see the road and the edge of the view tidy. The rest of the wisps from the evil one. In the furnace.
Cool night light;)) the Idea is good, the main thing is to not interfere when riding
Ahahaha, microphone Litsinger. I will hold you lips, I'll squeeze you hands. I feel so good with you I'll take you with me
Yeah...had a lot of things in life to see, but the micro. instead of a handle...but still with lighting...And it looks good...
Original!)
But I would play with the brightness would have made a much rotten, so straight could appear that night eyes didn't burn out) Or connect to the size — at include size, brightness decreased.
Yes, unfortunately, the first Association that popped into my head. Long had the series re-download, the grand tour series 8 to make a PrintScreen))
In General, it amazes me the algorithm of proposals from драйв2 how I ever got here👐
Well, if someone, at the sight of a microphone, an Association with the penis...And well the ignition does not like?))) Long searched for this picture? Or on the computer in the "Saved"?!)))
stylish-the fashionable youth !
did not even trouble to SLR took a picture of the creature
sorry in hell, for such there is no separate boiler )
Fucking genius! I was wondering where the microphone is burned day to throw a pity and it is no matter.