Haute couture front arm bushings (TRD) - Toyota Corolla, 1.6L, 1996
Ordered silent front levers on MacPherson strut from turbojet engine. Will be in 2 weeks. They say the arrival is noticeable, the car becomes more springy, we'll see.
My paragraph is long and irreversible. I rolled my lip onto the stub of the turbojet engine, but after the price was announced, it rolled up by itself, 15 pieces for a crooked piece of iron I'm not morally ready to lay out yet. Maybe in 2 months I'll be ready))) Or take a Piece, I'll think.
One figs need to do the suspension, there is no way to get away from it. In St. Petersburg, go, thundering like a tin can, I don't even want to :) Of course the links are thundering, but they have long been in the trunk, we will replace everything in bulk.
Wait, there is the same kind of silent front levers only together with the levers change.
They walk for a long time.
There is not a lot of money + they themselves are not expensive
in any way.
And how long do the pressed ones go?
How much does the procedure + new silencers cost?
How do they affect driving performance?
I was just looking for silencers on my own, and did not find them - on the diagram there is a lever + silent block, and for left-hand drives - separately.
Nope. New ones are pressed out and pressed in. Although many find it easier to buy new levers. If that - on our forum, a guy sells for 1000r each in new silencers.
BadCRC
No, they just say that they are weaker than stock in terms of lifetime. And stock can pass 3, it's like driving and on what roads.
5 for the whole - good) I have a current in front ...
I confirm, I took Novosibirsk polyurethane ... not solid, we left for half a year = (
under warranty they really changed, now they are solid, I hope they last longer ... but still I would have better put high-quality rubber, but there are no such ones. In the original there is the whole lever
Well, I don’t know if the silent levers have changed before me, but in my opinion I pressed out the original.
put RBI a year and a half already standing.
and before it comes out in 1700))))
No, they just say that they are weaker than stock in terms of lifetime. And stock can pass 3, it's like driving and on what roads.
5 for the whole - good) I have a current in front ...
Well, I figured that polyurethane from Vladik will come out just at 5tyr. only this for the whole car))))
And about the fact that the year does not pass, I strongly doubt it ...
Polyurethane is tougher, but they say it crumbles faster. And I, Micah, want to do it once a year, drive without thinking about the levers, and then take off the MacPherson strut and sell it in a pack, and put in the strat :) Also, the struts and springs need to be changed to screws, hmm ... In short, I need these silentlets!
For the price of the question, I wrote in the event itself - 5 thousand in total for 4 silence. Plus, crimping will probably rise in a thousand and a half ...
I take them not for the sake of reliability, although there is such a side effect, so to speak :) (they are cast, without holes, twice as long as the runoff run), but for the sake of suspension elasticity, they are stiffer.
How many pressed-in ones pass - yes, as much as purchased together with a lever. At the plant, they are pressed in the same way.
And if you need to - ask, I can tell you where to get these)) How do you decide to take. It seems like yes, in the existential they are not separately, silent. And there seems to be no turbojet engine there.
The trick is also what kind of silencers you have ... There are two types, it seems, round and not quite round))) I have round ones, I have never seen the second type.
Along the way, the right rear silent is generally a paragraph. Beginning to knock even under the pedals ... Hurry, new ones have arrived. Bumps have to crawl like on a stratum - barely, because faster - it thunders :)))
but in our city they also tighten up with polyurethane - I can't decide everything financially :)
Silents came, handsome men. Molded and resilient! I will put it at the same time as the swap, so as not to disassemble everything twice.
How much did it cost ?!
They're polyurethane ?! You know that there are Novosibirsk ones like that ...
Frost is on our forum :) By the way, he still has like 1 or 2 sets (ie, you don't have to wait from yapii).
Okstay, guys, why are you all obsessed with polyurethane ...
They are made of something of their own, TRD, such as hard black rubber. Cost about 2200 both, the rear are large. There are no front ones in Iponia ((((I have
n’t put it yet! A swap is coming, I will put off the suspension anyway, then I
’ll put it on.) As for whether there is in Novosib - xs ... I can give the contact of the person through whom I took in Moscow time.
and I ordered it at the fulcrum, put it in, and am not worried. for the whole before 1800r