Margula turns

the MOSFETs do the crumbs

This is the people, not to the functionality of interest and to what that edge. Uzhoss!

aleks5050

Easy — the factory send the sheet with boards and each circuit Board on the circuit Spud holes. Here you after willamalane shawls and turns edge of a wave

Well, it's not serious :)

For such boards do Scrib and just break.
But if the complex cntor, then milled. This yavo "manual" fee — the roads are clear :)

It is actually much easier))

Easy — the factory send the sheet with boards and each circuit Board on the circuit Spud holes. Here you after willamalane shawls and turns edge of a wave

Yes, it would be super! And another video how do you make wavy cost! Very much a come on)))))

That would be video to look...)

Becomes obviously clearer)) Thank you all for the info))

Will geomagic. Help only from electro thermal breakdown

On the one hand Yes, but on the other I have at one time burnt out on tiny ports and the driver chip when it was directly included. But there were jambs with the tiny power most likely lay.
So I prefer the machines at least, to put still.

High Performance Lights

Well I mean the size and more about what to keep in this form-factor may more than 15 Watts :)

There's the public wondered where the resistors on the gates of the cases? :)

Nagurny there rezyukah, nothing to restrict

Well Datasheet it is itself "read", so it is logical

Read "Power electronics" Semenova) there once again is written that from dataset for reference only))

Well, actually they're not needed especially at low voltages (5V there).
But on the other hand, I have a couple of times in this connection the transistor has remained open.
I usually put, ERU stupid datasite section measurements open time. Well, if you do not explicitly need otherwise.

I'm not asking where)) and just wondering)

Well I mean the size and more about what to keep in this form-factor may more than 15 Watts :)

There's the public wondered where the resistors on the gates of the cases? :)

High Performance Lights

Stephen, well, at least wrote, what, how, why.
What's funny turns "to margulici"? Or it is about modes "for fun", not when they are enabled?

I have a field researcher in the same housing stand and "hold" the power line xenon in my controller that controls the front light.
However, there chestemere, more copper and three pieces in parallel with the stock.

Yeah, the same, only green)

High Performance Lights

Well, judging by cetera the field workers.
Well, either two by two :)

Button is not very practical current. I am your driver "kept" under the hood and they are encapsulated termoperevodnoy. There's hell ponazhimat

There is access to a private external button is.

So I'm trying to understand)the Specifics can't find or can't understand, not famous world)

The theory you need to know. And why do I need a resistor in the circuit of the shutter

I mean the resistor of the gate at the field researcher, it turns out it is not needed?)

don't very understand the language of the birds :)

I just do not quite understand one thing...)) is Obtained using the MK Rg does not need to put, to limit?))

Well, judging by cetera the field workers.
Well, either two by two :)

Button is not very practical current. I am your driver "kept" under the hood and they are encapsulated termoperevodnoy. There's hell ponazhimat

I understand it is something like "running lights" with different effects)

Stephen, well, at least wrote, what, how, why.
What's funny turns "to margulici"? Or it is about modes "for fun", not when they are enabled?

I have a field researcher in the same housing stand and "hold" the power line xenon in my controller that controls the front light.
However, there chestemere, more copper and three pieces in parallel with the stock.

Will not. He nishano bridged GND on Long wires is not expected

Stepan, and input from external buttons no conder? It is bad...
Drawdown will be spontaneous or unpredictable behavior of the controller, especially in wet weather or when long wires to the button, software contact bounce there is not going to help.

A scheme, firmware and all that?)))

is it possible to make a "Pribluda" for the turn signals, one incomplete turn signals and times blinking lamp on as many new cars?)

Show me photoresit this step

On the file it does not. It seems that used the old cutter for photo paper. They have a different profile there.

File

Than you cut the Board (it turns out ribbed)?

Cool!