New things: 1 — device DRL from MGOOK. 2 — Retropalooza
Before collecting the DRL far in panukala such a plan: DRL (DRL) — Daytime running lights. Far in polygala. Build+install
Now I decided to try a version of Maxim MGOOK
The new version of the controller, DRL
He looks a little handkerchief, so that the components were closer to each other. Just practicing the drawing Board )
What are the advantages of this option, DRL saw for himself:
— compact (shrink to fit)
— unilateral fee (ease of installation)
flares after 10 seconds after the ignition is turned on
— the heating fee is small, used IRF 9310 (compared to the IRF4905 , almost not heated 9310-e transistors)
Diagram of the device shown below.
To check will need a battery (or power supply to 12V), the 12V light bulb.
Join in the diagram below. As keys S1 and S2 it is possible to use transactions that are close to the minus (in the case of the withdrawal of RUCH), and to focus on the +12V (in the case of output to GAB). A short of these wires to the poles of the power supply simulates the operation of locking is a fading lamp, simulates the triggering of putting on the handbrake and the inclusion of beam.
Wiring diagram to check circuit Board on the table
Algorithm of operation: after power on the Board is aged for 10 seconds and is a smooth inclusion of lamps. In case, if you can complete the insights RUCH and GAB on the minus and +12V, respectively, will be the attenuation of the lamp.
If you reverse the polarity on the findings of RUCH and GAB, i.e. if there is not connected wrongly, then the device will not burn, just won't work as it should and all.
If you mixed up the +12V and minus on the Board is also not a problem, there is a diode protecting against incorrect switching.
Adjust the brightness
To adjust the brightness of DRL, there is a button on the Board. The level is set from 5% to 50% in increments of 5% each subsequent click. I.e. a total of 10 brightness levels.
To configure the device, you have to enter the service menu. To do this, with the device turned on and erupted lamps hold the button in and hold it about 2-3 seconds until the lamp flashes twice.
All mny hit the brightness adjustment mode.
Now press the button and the brightness increases. Reaching the Maxim possible in 50% of proishodt reset to 5% and so consistently in a circle. After selecting the desired brightness again hold and hold until until the lamps migot twice. Release the button. The brightness adjustment is finished.
Led retro-carrying in the car.
In the garage I guess many have this flashlight as pictured below.
The idea of replacing light bulbs for LEDs is not new, saw the alteration of such a flashlight to drive at least two people.
Sent Alex 3nergetik led strobe light, asked (I don't what it was) like this: Led strobe to a 2-channel (PIC12F675)
In return, at my request, received a fee for the flashlight.
Immediately covered her lemon varnish. Do, Shine perfectly )
The only disadvantage of this carry is that she has no folds compactly into itself. If before the cord is unwound inside carrying and carrying itself was covered with a lid, but now everything does not fit inside.
Now stocked with LEDs 5050, 5630 (or 5730 can't remember exactly). We need to check at work which have a maximum current consumption of 150mA, the only cooling you need to provide
Yes, finally scored and tied the card to make purchases from China. A lot of any useful-besplatnosti is on the way, we only expect
Good luck to everyone )
himiks
default frequency is 9.6.
there are fuses in MK by default, 6A FF.
but the idea is critical fuses were not supposed to participate in the crafts and the idea firmware normally be filled
reset the fuses with the programmer. According to the new without problems screwed.
Understood. To 4.8 Mg to put in the calculator for fuses LOW 69, HIGH FF to prescribe.
default frequency is 9.6.
there are fuses in MK by default, 6A FF.
but the idea is critical fuses were not supposed to participate in the crafts and the idea firmware normally be filled
Probably have to buy another MK and sew again. If the fuses do not touch, the default frequency 9.6 ?
why first firmware, because when setting the fuses you may want to use the leg reset is порт5, or leg 1 of the microcontroller. That's when it is activated MK will not be defined, and the firmware will not be able to fill.
so it is always — first thing — firmware (flash, + epprom, if there is such), and then the fuses
himiks
Triton didn't use it so don't know what's there and how
13 in the same way as 13A is programmed.
first, the firmware is uploading, then the fuses are exposed
if you are unable to set the fuses, it is possible from the factory (nothing exposing), the author says it does
I put the fuses, then the firmware to roll tried. Thanks for the clarification
need an alteration in the firmware anyway
since the response size is present or not +12V
a reaction to the speed sensor is a frequency signal (pulses)
the dimensions can be such as to communicate with the speed sensor? the necessary alterations in the scheme?
one fee for two lamps.
transistors 9310 , current up to 20A each. Consumption of about 5-6A, the heating is small, the radiator is not required
Wiring diagram to check circuit Board on the table
in this scheme, not a typo on the contact GAB it is not to the advantage of the pull up? nansana to the body of the car and the circuit connected to the positive
greetings, is the place to be.
if split + into two components: from the ignition and battery, then one can leave
Assembled the unit and installed according to Your instructions, but after connecting some time later found that when the engine is stopped with the blinking of distant (lever itself) switches on the ignition! What could be fault?
MaximMS
And where is the firmware?
www.dropbox.com/sh/g6hweo...duiLxRMU3yIKbNpe1Tza?dl=0
try on the light bulb, not led
it's the same for halogen lamp device
lamps have a large inertia than the LEDs, and there pulsations should not be visible
Thank you. Collected debug scarf and there is a BUT... IN the operating mode the led lights up gradually, gradually goes out (slow pulse). What could be the reason?
as you prefer, and do it.
Want after 5 seconds, set 6A
This device work on the brightness and the modes are not affected
himiks
4.8 exposed
the comments have the right information, look below
If the 4.8 MHz in the LOW fuse you need to register 0x69? Well, that's when the setup 0x69 I start the DRL starts after 15-16 seconds? and when you install 0x6A — 5 seconds. So, how was it?
hi, actually took such transistors ru.aliexpress.com/item/50...10208.99999999.286.MVBQey
they brought me, on one DRL overheated, killed the charge, and the burning smell in the car
think how to protect the Board from such overheating?
already thinking of starting controllers for other types of transistors, they turn off when overheated and is controlled KZ, old model, long used in cars, but time-tested
ru.aliexpress.com/item/Fr...=2114.13010608.0.0.cNcJFn
but I don't know how they will work on PWM
I took ' em. There reviews I one star set and wrote that it was a fake. Why is it under amerikosovsky flag. Heated but work. Can three put.
thank you, I'm still looked after, will taste, and then accomplish your goal
ru.aliexpress.com/item/50...10208.99999999.286.MVBQey
Here ru.aliexpress.com/item/IC...=2114.13010608.0.0.qDoYVe I was the only who bought them, in the opinion wrote that they are the same as with Chip and Dip. Why is there under my nickname flag amerikosovsky. And for 11 rubles heated to 50 degrees but still work, my brother and father on machines with the same transistors for several months working.
the chip dip has gone, I last took, now writes that they are for 240 rubles apiece
PS just gone 290 p., such things
a reference to Ali, who as cidip not heated, it is necessary to buy, and deficit
On Craigslist view. Controller of quality electronic components 500. I personally took Ali transistors 9310 for 11 rbl./piece — heated, at 16 rubles./PCs. — heated, the Chip and Dip ordered 50 pieces you can tell are not heated with two lamps 55 watts, you can even put one instead of two. Then Ali found the transistors for 33 RUB./here they were both on the Chip and Dip for 43 RUB./
Tinku in a small package to solder on the PCB this can
the alternating wide and narrow packages these Tinkoff
himiks
And most importantly 7413 is the N-channel transistor
but the circuit uses P-channel transistor.
Conclusion: 7413 is not good in any way
Try to replace IRF9321, or what. IRF7425
Yes, I have twice made a blunder, alinico in a small package took, so the cost gonna have to redo it
even in the store under the order, only waiting for two weeks...
understand about waiting, just want to pick up a kind of fuse ran out. And then a few weeks may no longer want to collect.
alas, the Internet shops don't know on the radio
like www.chip-nn.ru you can see from the tda2000 once some relays ordered.
but everywhere it is necessary to compare
about Ali we know and buy, but if talking about one mikroshemka, then wait for a month not kamilfo, then when she comes I can forget why I ordered it,
it is necessary to start ponakupit parties different mikruh, but the difficulty is that at the stage of studying don't know what's useful, and then finally stick on some kopeiskoe position, and still have to speed to break into electromags
I was just thinking You know the shop is good, whose prices better of chipipa and delivery in the area of the week
ebey and ali is not a competitors chip dip and Vice versa.
don't understand people who are in the chip-dip to buy the items.
let me explain: the price tag is initially a horse they have
example even Omsk on our store
1) DAN — attiny13 in a wide case — 40P
www.danomsk.ru/shop/2-mik...attiny13a-su-so-8w-atmel/
2) but the chip dip he 90R
www.chipdip.ru/product1/8521272104/
PS: even in our not-so-cheap store comparison, you can see
-----------------------------
cheaper than eBay and Ali...
only Tao Bao, but there is a special registration and all non-Russian, not even English
and except for ali who can compete with capdepon? tell me
and chiptip fed up with their prices
the price tag from the ceiling
the difference with China, about 10 times
"Chip-dip" is used only for the search of analogue transistors
ordered last week of 6 pieces
chiptip something very bad was already a week taking, I thought to buy more of them
and here: www.chipdip.ru/product/irf9310pbf/
ohreneli chtoli, where the price tag?
himiks
And most importantly 7413 is the N-channel transistor
but the circuit uses P-channel transistor.
Conclusion: 7413 is not good in any way
Try to replace IRF9321, or what. IRF7425
IRF9310PBF for 43 of the ruble, this is normal?
expensive as it is, or they t on cost?
Yes exactly, I'm a little rlsu he realized. yeah will have to order and wait
maybe better to put these, a little cheap, but it will have cost to redo it
www.chipdip.ru/product/irfr5305/
And most importantly 7413 is the N-channel transistor
but the circuit uses P-channel transistor.
Conclusion: 7413 is not good in any way
Try to replace IRF9321, or what. IRF7425
a suitable irf7413 is IRF9310, others not found in our farm... a little later he added:
the campaign is weak, burn nafig, and if you alter the cost and four to naphat?
the condo is on the minus or plus? if numinous, almost nothing needs to change, just solder
else noticed this feature in other crafts.
The control button is best to put ceramic capacitor (100нф) (parallel with the button). Eliminates interference on the set. And then on the garland "dual smooth ignition tidy", when touch and configure parasitic capacitance is formed and glitches fees inevitable
himiks
Zener is dead it turns out
in General, I won, thank you very much, did not understand what it was, the campaign still the same Shorty
and the voltage small, this is when Tinka died, generally without loss))))
the condo is not put between the earth and the dimensions, standards and so it, the stand was heaps of noise, and the scheme was not full, but put a tantalum and ceramics after another diode
thanks again, I will mention You in BJ
himiks
Zener is dead it turns out
replaced the Zener, it is still of 1.12 volts that nafih
himiks
hi.
what are the values of the chain connection scheme?
photo card is ready to see
the campaign was koromila transistor, a little moved, but now another song, Zener just 1.4 volt, it is not heated, but CeTO is not enough, the scheme does not work
I would have done,
in this Board, because you can just add a capacitor on 100нф between dimensions and a minus.
If that doesn't work, put a diode on the input envelope.
But the chain of Zener have not seen here.
To test empirically, solder the resistors to 4.7 2.4 to 5.1 in the stub, the capacitor 100нф (figure cited earlier)
himiks
Leave keramiku on nutrition in 8 leg., in parallel, the top is soldered castalloy.
good evening, what is not matter, it is heated very strongly, the first was soldered
BZV55C5V6, then soldered BZV55C4V7, which is generally just fade
with such dimensions should not be
we must then try to remake the chain dimensions.
For noise immunity instead of a simple voltage divider (pair of resistors), put the Zener diode and the capacitor
here is an example of the picture, on a 5 - foot MK
d-a.d-cd.net/1973becs-960.jpg
+ else input capacitor on 100нф to put
-----------------------
Try to put in the fact that there is already another capacitor at the input to 100нФ relative to the earth
not looking for easy ways, modified the schema to put SMBj18a, added another capacitor, and I at the top of Your resistor 47к not like it, You have it to the positive after-effect transistor, and it is necessary to transistor meshing, maybe there really is no difference, but made according to the scheme, as well the condo I have a lot of tantalum, ceramic top does not work, and the clock button is stupid, I'm afraid the corps will track to short, so a little pushed from her path, cost a little expanded, a few millimeters does not matter
and what firmware? everything works fine, except for the inclusion dimensions, if put on the handbrake, then OK goes smoothly, but if you throw the input size plus the lamps start to fade gradually reach zero, then gradually turn on and so on, but not off, this is as it should be?
then you want a few here such to buy, to test:
www.chipdip.ru/product/irf9317pbf/
and that can knowingly overpay))))
then the seal will have to radically alter that will lead to a significant increase in fees
right to put all the capacitors, I have some in signet not.
Of course it is better to put before and after stabilizer for ceramic and tantalum condenser
tell me, and here capacitors c1 and c2 from the circuit, your signet is excluded? nawash's signet in General, only one condo, but in the scheme of their 3...
and in the pictures the feeling that they alternate on one ceramic Board, the second tantalum is or it shines so?
on the breadboard collected all flashed, it seems to work, now it is necessary to etch, tin plating and soldering
Hello again, here I sit and look at capacitor c3, traveled half of the city is not found suitable, but there is the same, but at 10 volts, in theory the measurements in this place is just 5 volts, I think to put them, sort of not critical the same
in the diagram, R2 — 47k, it is. 473 resistor is 47к. There is a photo on where to put and 513.
The Board has under 100 Ohm resistor. It is just a
tell amp-TA, the diagram R2 47к, 4.7 is supposed to be? and on the Board don't see the R8, are they?
can not touch, and there's what the author says to change frequency only.
in any case, it will work
himiks
below in the comments look, the link given there
the fuses are untouched I hope? ))
now have little time to collect
I don't remember when soldered something devices last
Hello everyone, I understand many gathered and all earned DRL, can someone tell me. Assembled the circuit, when connected from the lamp to 100% and belching smoke of the 2N7002. Thought that are poorly collected, repeated on another piece of textolite and the same thing happened. I noticed that in other schemes instead of the 2N7002, the transistor is BC817 and generally drizzling.
In the wiring diagram to check circuit Board on the table, clearly chaos is happening. There mixed up the names of the inputs and potentials.
Signet also the scheme is not consistent.
in the comments, below
duplicate again
www.dropbox.com/sh/g6hweo...duiLxRMU3yIKbNpe1Tza?dl=0
TOCEAN
I meant the previous, it is taken from here nsskn.narod.ru/pwmheadlamp/prg.html
And another question, the fuses as you have in firmware of this topic
the fuses for this version of this article can be left standard 6a ff
No you do not understand a bit, with the version I just did for myself pierced as if for practice.I want to take your piercing and collect the scheme, with Krenkel and four field workers and control keys, and I want to ask you what else you need besides the flash file to do. and flash it with lpt port 1
in the subject the legs and control on the other made. If the device from this version to fill in, work should not
I meant the previous, it is taken from here nsskn.narod.ru/pwmheadlamp/prg.html
And another question, the fuses as you have in firmware of this topic
Welcome.
1）you can flash any available programmer.
2. I do not understand about the past and about previous firmware. For this device one IOS, kommentariyah reference.
Hello, if you flash your latest firmware via lpt 1 port, or doesn't work that way .Just today flashed the previous firmware, checked the led., works., while the programmer in the way decided to try.
No I'm not talking about the weekend, it is clear, I'm talking about the one that management is
in the previous was the implementation of the scheme is different.
There is enough IRF9310 2 PCs. in case so-8
But at THE 220 that was — they have a strong heat, because the internal resistance is large
And a single transistor to control the opening of the output stage missing, and then look at the previous diagrams are of the type composite in the management of
Comment has been deleted
1)the rule to include bipolar: (for BC) to the input of 1K Ohm, tightening to minus 10K.
2) inclusion rule polevikov: (for 7002) to the input 100 Ohm, tightening to minus 10K.
you can even though to put
8 foot relative minus sign must be 5.1, and no more .
MK 5,6 in not working. check his food, it cant
Without the resistor in the fifth leg of the norms of Silence at the output. 8 foot 12V. Two stabilitron checked. Both on 5.1... Attiny13 alive. sewn read. Two things to try. Scheme 5B something is not so working
Comment has been deleted
otpaivat from the 5th leg of the resistor. and look.
if it works, immediately turned on the lamp means a joint in a transistor circuit
if you do not turn on lamp standards.
next.
measure naprugu on the power of MK, if 4 to 8 feet, stress no more than 5.1 V. if more, the Zener diode scribe.
then look at that output from the MK 5 foot.
There should not be more than 5V