led backlight automatic on ТЛК200
here is the place illumination the automatic transmission.
since the purchase of the car the selector is not lit. as it turned out. there burned a lamp=)
I didn't know, and the owner thought no backlight at all =)
in General, the light source there was just the same as I did on the Aveo bulb with green londontom =)
the complexity of changing the color and changing to LEDs is that lamp look 4 guide.
so they all got their, it was necessary to scratch turnip...
the LEDs I got 5630 (palletnye) due to the fact. the optical fiber is unpredictable. the area of the light source the more the better. similarly, the power in our case, not much happens.
as the time was almost 23 hours of install has been postponed.
presumably a couple of days, expect =)
supply current of four series-connected LEDs made up 15 mA at 13 volts.
LEDs have a maximum speed of 150mA
materials:
5630 samsung 4штуки
nsi45020 one thing
the Micarta double-sided (on-table pruning was lying)
a bit of tin, and many many patience...
Full size
Full size
tleher
Good luck in your good undertakings)
And more and tidy it is! There are 2 blue ones such 😄😄😄🤗
Thanks for me it's not the first of course but always interesting... will Do the same orcatec, by the way in the glove box there is still the process to finish ( the box under change the filter ) so as not to pull raised panel every time! Usem electrical mini led good luck, and let there BE LIGHT, because soon NG!🌲🌲🌲⛄this💥
It should also not bother also illuminates the selector and the thoughts still make the light on the diodes in the glove-box there, too light, stunted and light in place of the cigarette lighter and it is not lights or anything maybe even a Cup-holder where the armrest! Led tape is lying idle, it is necessary to picolinate...
there were I work much smaller, there is a difficulty in the idea was. this is the result of the second attempt. the first was just on the wire are collected.
the car is 08 model year, the change of the light source entails a lot of processes.
well at least what it is not (yet found me, the process is not complete) the only bulb in the interior of the light of cryptograms
Instead of having to install a few cheap LEDs, they put the antiquated incandescent bulb with an equally antiquated mondonico and design and then make montaillou design plexiglass... Sometimes I our narrow-eyed friends don't fully understand...
XS well, personally, I have nothing to be watched
and so, capacitor and diode save from "needles". It wasn't exactly their LEDs and fear.
ideally, it is true, but in practice I have a stereo hanging from the relay. Also saw how buggy autostart on the alarm, the replacement of the blocks did not help. Oscil I didn't connect himself to the system, but people said that peaks there, plus or minus a hundred are.
and where did it come from the battery? all modern cars have a damper diode in parallel to relay coils, and fan motors, stoves, etc.
in extreme cases, the led emitter can be bridged anti-parallel diode in reverse polarity. But for me, it's too much
the voltage in the battery — do not care, led to important current. Which pulse can exceed up to 10x, but under the condition of cooling of the crystal.
sure) I personally think the 3 watt led has a very horoshuu that is to say the strength of the crystal are relatively weak brethren that the battery in the car is important, jump in it more than 100 volts as direct and reversed polarity good hit the crystals, 500 a lot of resistance at 3 W crystal have "children's" load and do not care it on the "dirt" from the battery.
short circuit
5630 running on a current of 15mA, this is, of course, a severe overkill
about how to ride a super-MAZ in the store for half a loaf of bread.
and so, respect, good work
I, just yesterday, did exactly the same at 1M Focus with stick automatic transmission, but I yuzal a piece of tape with 6pcs 5050, and further reduced the current resistor 30%
so this is the awesome solution I have for example in the illumination of rooms and doors are 3хваттные LEDs, also 10-15 milliamps they filed, and bright and will not burn out probably never.
Primitive Board quite would suffice. There is a place under the charge extremely convenient. No, you need a lot of fibers and filament lamp...
clear. I'm also a little@#ate to the shape of the glass. Here's the samurai: a heroic pose their own difficulties themselves heroically solve them... In 2008 was already more or less decent LEDs, not to make a fuss a hell of hell with such a lightpipe
There is unfortunately extremely complex light guides. Had to Dodge on the situation
5630 running on a current of 15mA, this is, of course, a severe overkill
about how to ride a super-MAZ in the store for half a loaf of bread.
and so, respect, good work
I, just yesterday, did exactly the same at 1M Focus with stick automatic transmission, but I yuzal a piece of tape with 6pcs 5050, and further reduced the current resistor 30%
I'm also pretty surprised. I'll tell you that they found another two filament lamps in the buttons. Thus, there are only three in the cabin...
dizog
Nicehome you what you are doing. ...200 with a soldering iron. ...words, the hosts 200 😕
ТЛК200 normal trash mass consumption.
tleher
You are very right about people.
Bright work? Probably distracting but the light bulb with santonicum intimate muffled
You sorry, the person need? Lengthy to sasnetsi is certainly fine, however it is better in the case of questions to ask.
Nicehome you what you are doing. ...200 with a soldering iron. ...words, the hosts 200 😕
clear.
and there is some light glue for such purposes to the led from the inside to glue to the letters and that he shone through the glue?
As asked, did. By far the incandescent lamp to leave would not. The color from her yellow. And need a white backlight. To do an the selector is not fast, need fitting and adjustment. The car is not in place, each time caught to figure out how come it's terrible.
why not stick a lamp that there are and should be?
and it turned out a garden peremudrili technologies.
the Japanese are perverted as they could with optical fibers to plug the lamp, and You have perverted not less, adjusting the LEDs in place of bulbs to use fiber...
why?
you could already throw the fibers and put the diodes directly to the lumen of the letters than to fool for nothing?
am I wrong?
To all together to shoot, need the owner to catch) gets, I will lay out the material
Great! Still photo how it looks "Assembly"! Why in advance not to do at the factory good with white backlight ?! I'm still in Racice and all interior lights converted to led — light to order more!
That is in my post You do not understand how I changed the light bulb to the led?)
Maybe a little photos and information. So I past this record just passed, not interested in the view not informative
I have bigger and faster, why is my post not post in a electrician? www.drive2.ru/l/8317680 And probably had the magic word TUNING to write in the header? Well that's definitely not tuning, my dear, this style change!)
vasyna
On RR recently rode. There is generally a Twister ) feeling control of the car, more like a dream accountant:
2221 year. The accountant walks up to the computer with the 1C version natsat and says — "I Want!" And 1C does well )
So snake with a lever something.
So not interested. You need a sense of control over the situation
vasyna
On RR recently rode. There is generally a Twister ) feeling control of the car, more like a dream accountant:
2221 year. The accountant walks up to the computer with the 1C version natsat and says — "I Want!" And 1C does well )
So snake with a lever something.
Twister, by the way — thing!
Specifying as 1C-nick former. It's almost like this. 90% of young accountants don't even know what for, what transactions, etc. They know how to press the button 1C. What can I say, I know of an accountant in which has added transaction entered in manually removing rent income from the Foundation's RFP so happened that over 5 years of work in 1C (before and it worked and the account was conducted on a piece of paper with Excel) the Director did not receive the RFP 1000000rub. And she talova assured that rental income in the RFP is not, not what side. So that part is already happening.
ExpoLeafovod
I hate selectors-snake... who invented them and why?
On RR recently rode. There is generally a Twister ) feeling control of the car, more like a dream accountant:
2221 year. The accountant walks up to the computer with the 1C version natsat and says — "I Want!" And 1C does well )
So snake with a lever something.
Rom-51
This is for a smooth transition with the mechanics :)
Went direct the selector button on "snake" look is not necessary and there are no errors of inclusion of transfer.
I'm not arguing with You, just HARD and not everyone will be able to do SO!:-) IMHO
Beautiful, hard and a lot! Is not it easier instead of incandescent ONE scattering the led stick? And why the fuss? IMHO
Welcome. About avensis will not say, because I do not know. In a Toyota Camry the same light. Logic dictates that the backlight needs to be
Hello! Please tell me, in avensis 2003 must also be the backlight? When I bought it there nothing was burning and now not burning. But after seeing your post thought it should be or not
Already...(( There is a video step-by-step until the Central tunnel, and the most sockets of this — no(((
Hello. Can not know. I wore the parsed elements. I'm not picking. Maybe in the YouTube search? The machine is quite old, should be a video...
Good day! The question is not quite the topic of discussion. how to remove the console itself/plateau lever automatic transmission (where letters P-R-D-S)?