Cruise control and radio control on the steering wheel. - Toyota Corolla, 1.6L, 2008
Free time appeared and I sat down to write a report on installing Cruise control and radio control on the steering wheel on my car.
I bought all the parts from Exist. List of ordered parts:
1) Toyota steering column switch;
2) spiral wire;
3) left and right buttons;
4) the steering column switch wire;
5) steering column plug.
Everything cost a little more than 9000 rubles.
Required tools: screwdriver with cue ball - cross and T30 sprocket, socket wrench with 19 "head.
For owners of 17 MMT and 32 configurations, replacement of the coiled cable is not required.
We put the steering wheel and wheels in the" straight "position.
We remove the terminal from the battery. We are waiting for 2 minutes (according to the manual) and remove the two plugs from the bottom of the steering wheel, then unscrew 1 screw on each side using an asterisk (the screws are tightened quite tightly - do not save on cue ball, do not turn off the hexagon).
Remove the pillow and disconnect the wires. We put marks on the steering wheel and steering shaft to align them after removing and installing the steering wheel in place. Unscrew the nut with a key.
We remove the steering wheel.
Remove the bottom of the casing, disconnect the wires and remove the coiled cable from the latches (3 pcs.)
We put a new twisted cable on the latches and connect the wires.
We put on the cover and break the safety stopper (it prevents the cable from rotating during transportation and keeps the middle position). At the same time, we try not to turn it before installing the steering wheel, the connector should be on top.
We fasten the steering wheel in place, combining the previously applied risks.
We connect the cruise control wire and fasten the joystick with two "clips" (ordinary M5 screws 10mm long with washers, you can not order 4 pcs. For 100 rubles, but find in the closet).
We fasten the buttons, lay the wires and connect the connector to the coiled cable.
For the connector that remained "not sewn the sleeve", it turns out that there is a special place (I thought about 15 minutes where to attach it, then it dawned on me - bourgeoisie, eh!), Just inserted into the hole and that's it, but it doesn't connect to anything.
Now the most important part of the job is cutting the ears at the pillow.
It is imperative to remove the stiffeners, as in the figure, because if they are left, they rest against the side of the buttons and the signal is not pressed.
Arm yourself with patience and everything will work out!
Happened? Fine! Now we put the pillow in place, making sure not to pass the wires. We tighten the familiar screws, put on the plugs and the battery terminal.
We start. Everything is working. By the way, the buttons are coolly highlighted when the dimensions are turned on.
All! If anyone has any questions, write to try to answer!
Good luck!
PS Don't forget to wash!
Price tag: 9 200 ₽ Mileage: 45 500 kmI have long thought to put myself on a cruise, but even like that hands do not reach! And it's a pity for money! Although the thing is not controversially useful and convenient!)
Well Andrey is great! All by myself, great job! Thanks for the report, it will suddenly come in handy! ) A cruise is a necessary thing, especially if you are going to go on vacation! )
Good report. I would have long ago set myself a pity that the 1.4 engine is not allowed.
I do not argue, he is with mytoyota.su. I did it according to him. Many have made their cars from this report, and I think they do not mind that it will help someone else with Drive. For this they have great respect and respect.
Thing, handsome. I described everything very well, when funds appear I will definitely use it, Get gratitude and good luck on the road
A very useful cruise thing. I tried it on a Camry - just dumbfounded. But I don't use the buttons at all, my hand itself reaches for the radio tape recorder. But it looks good. Congratulations. Tell me, how much did the cruise cost separately?
I also forgot the plug on the casing - 62 rubles
Most likely, a twisted cable will also have to be ordered. There are no paddle shifters on the machines, and therefore it makes no sense to install a cable with a full set of connectors at the factory (which is done mechanically).
The cruise itself costs about 1.5 thousand rubles, I will definitely not say exist prices have recently raised. You only need a switch and that's it, 2 screws and you can buy in the fasteners. It will be cheaper)
A very useful cruise thing. I tried it on a Camry - just dumbfounded. But I don't use the buttons at all, my hand itself reaches for the radio tape recorder. But it looks good. Congratulations. Tell me, how much did the cruise cost separately?
I'm always going to the nearest cities (Surgut, pyt-yakh) every time I remember - oh, how good it would be if only put on a cruise))) ... It's good that I put it) it will come in handy more than once)
In my opinion, it is because of this wire that the buttons do not work properly. Thanks for the info.
what happened?
There are 2 types of them, for a bare complete set where the spirals under the airbag and the signal, and heaped up for buttons, cruise and the above. Code on exist.ru 84306-12110
It looks like the coiled wire will need to be replaced. Can you give an article for ordering on existential?
That's for sure, you already had buttons and you don't need to change the spiral wire.
Andrey-M
Great, happy for you, myself while in thought.
Buttons came, installed, conveniently. By the way, the installation is much easier on the Prestige package. You just open the steering wheel, disconnect the old buttons and connect the new ones, and close the steering wheel. You don't need to remove the steering wheel itself, and you don't need to cut anything either. The main thing is not to forget to remove the terminals from the battery.
Tomorrow I'll pay and wait for the buttons on the steering wheel. In the meantime, I point my finger at the display, while moving my gaze from the road to the display. Inconvenient.
I was offered a phantom in 2008 when I was buying a car. But there the matrix was too coarse and the picture was correspondingly disgusting. But now it is a completely different matter. We replaced the matrix and, as the seller said, we removed many more jambs. But for three days of use, I can say that there are still joints. In particular, it is difficult to access the Internet, glitches with the detection of a modem, incorrect operation of the browser until I figured out how to access the SD card (the one in the upper left corner), there is no hole for the stylus, etc.
But otherwise I'm glad: a rear-view camera (after the date I'm very used to it), TV (you need a powerful antenna), navigation, DVD, a convenient radio. Even the sound is better than the native head. The package contains all the necessary cords.
The phantom got it that week. Because of this, I decided to bet. It's good that I got to you. And I didn’t even know what it was. Thank you.
The buttons with the phone come in one set with the radio control buttons, there are 3 types of them
1. The radio buttons and the plug (like yours)
2. The radio buttons and the speakerphone function (like mine) are the cheapest option for some reason.
3. Radio buttons and speed limits (but this function does not work on yours) The
option you need on exist.ru has such an article number 84250-12020 , you go to the exist, register, fill in the part number and place an order, they do not work on the head unit , you need an analogue of the Phantom or Supra or any other that has a steering wheel control function and a speakerphone. Then everything will be good
Tell me how to order buttons with a phone on the eksist, i.e. what you put on the right. Please detail. Very necessary.
Comment has been deleted
I sometimes use it in the city, in the evenings, when there are few cars. Really like.
Thank you! Works on 5+, cruise maintains revs in a given range. Whatever speed you set, that one keeps, it works from 40 km / h.
In the state - yes, but I already have a supernumerary head. Any ideas on this?
There is no telephone in the staff, I put buttons for the future, I was going to change my head, but now it probably won't work, I'm going to change the car, and I'll change the buttons to limit the speed and control the tripcomputer from the steering wheel!
December will come and it will become clear. I have a 1.6 mechanic, there is a pioneer head, in an amicable way I want to control it from the steering wheel, the phone too. Well, the cruise, of course, is also interesting.
PS: Do you need understated springs? :) My car with full gluing and equipment turned out to be too heavy, I will change it back to regular ones.
Very convenient, I go and bastard! What details will be needed? All or just a cruise?
Ay well done)))) I have been dreaming and wanting for a long time. Cruise + radio control from the steering wheel, this is perhaps the only thing, besides auto-correction, that I want to put on the car ...)))
please tell me what is needed to set the cruise? do you need to remove the steering wheel?
Is there a radio control on the steering wheel? If there is, then you only need to remove the airbag on the steering wheel, if not, you will have to remove the steering wheel completely in order to change the spiral contact.
I ordered on exist.ru, the cost is about 3500 rubles. Here is a catalog for spiral contact 84306-12110 , shows the cost of 3990 rubles per piece.
It's strange, in theory, the car hasn't changed, maybe it's just that somewhere there are no fuses, when I put foglights on the box, I didn't have a relay, there was a connector, but there was no relay, but someone had it. We must try to ring the chain.
Thank you, on my 2008 everything worked out, I put my father on the 2011 Corolla, it didn’t work, there wasn’t even the “cruise†inscription on the instrument panel. So the kit is free to whom I will share. [email protected]
ugh, great, thank God ... I was afraid to order ahead of time ... thanks for the quick reply ... :-) went to stir up ... :-)
Hi Roma! No, you don't need a spiral contact. In this regard, you are lucky, it costs about 3,500 rubles.
Andrey-M
Roma, hello, I'm sorry I didn't answer for a long time, there was no time. Part numbers on exist.ru that you need:
1) Cruise control lever --------------------------------- --- 84632-34011
2) Steering column switch wire (cruise) -------- 84633-48020
3) Steering wheel plug -------------------- ------------------------- 45186-12010-B0
4) Spiral contact ---------------- ------------------------ 84306-12110 (you will need it if you have a simple equipment 1.6 if 1.4 - then forget about the cruise).
Andrey, well, everything, everything is fine on the first question, I found this stub. But the second question remains open.
How can I tell if I need a speriform contact?
Andrey, I can’t find a steering wheel plug, 45186-12010-B0 , in Exist . Help me find, or give me a link.
And yet, Spiral Contact, do I need it or not?
Rom-ka
Hey, are there any part numbers? give, huh? :-)
Show pictures where and how is the cruise control knob?
I don't have a cruise, which unit do I need?
Show a picture how the buttons are highlighted?
Roma, hello, I'm sorry I didn't answer for a long time, there was no time. Part numbers on exist.ru that you need:
1) Cruise control lever --------------------------------- --- 84632-34011
2) Steering column switch wire (cruise) -------- 84633-48020
3) Steering wheel plug -------------------- ------------------------- 45186-12010-B0
4) Spiral contact ---------------- ------------------------ 84306-12110 (you will need it if you have a simple equipment 1.6 if 1.4 - then forget about the cruise).
I will give the numbers, but there is a problem with the pictures, the car has been sold for almost a year, I will give a link to the original source, I will just get home.
Hey, are there any part numbers? give, huh? :-)
Show pictures where and how is the cruise control knob?
I don't have a cruise, which unit do I need?
Show a picture how the buttons are highlighted?
Lexa174
I have a 2011 comfort + car, automatic transmission, what do I need for a cruise? tell me!
If you have a full-fledged automatic machine, and not a robot, then there are no paddle shifters, and most likely you will need an additional spiral contact.
In theory, only the cruise control lever, the wire to it and the plug on the steering wheel cover, but I could be wrong. If there are radio buttons on the steering wheel, then only a lever, if not, then the spiral contact is also new.
I have a 2011 comfort + car, automatic transmission, what do I need for a cruise? tell me!
Rom-ka
So, I have a robot, I have paddle shifters - this means that I do not need a spiral contact. OK?
The engine displacement is 1.6 liters, which means you can put the cruise control. OK?
Where to look for cruise control relays and fuses? and then suddenly they are not. Under the hood or under the hood?
And, please, tell me the number for the buttons on the steering wheel ... I have buttons on the left, I want them to be on the right, they are just for cruise control, as I understand it? :) otherwise I can't make out the number on the photo ...
Thanks for earlier. :)
Found buttons, I don't have one on the right either, there is a separate one for the right side
Not in the standard head, but if you plug in the Phantom, it will be controlled from the buttons.
I can't find a plug in Exist ... of course I'll try it again, but says that there is no such number ...
And yet, if you put buttons on the steering wheel to control the speakerphone and bluetooth, where is this speakerphone and bluetooth in the car? If I put a Phantom mafon with a navigator, etc. etc. there is this same bluetooth, can I control it with these buttons?
No. The buttons on the steering wheel on the right - control the bluetooth and speakerphone, on the left - control the radio. The cruise is controlled by the "Cruise control lever - 84632-34011 " lever .
1. Pressed a button on the lever - the cruise was turned on.
2. Short press down - the speed is fixed.
3. Has slowed down, short-term lifting up - return to the fixed speed.
4. Pull the lever towards you, reset the cruise memory.
5. Raised up and hold - a smooth set of speed.
6. Dropped down and hold - smooth speed reduction.
7. I pressed the button again - turned off the cruise control.
So, I have a robot, I have paddle shifters - this means that I do not need a spiral contact. OK?
The engine displacement is 1.6 liters, which means you can put the cruise control. OK?
Where to look for cruise control relays and fuses? and then suddenly they are not. Under the hood or under the hood?
And, please, tell me the number for the buttons on the steering wheel ... I have buttons on the left, I want them to be on the right, they are just for cruise control, as I understand it? :) otherwise I can't make out the number on the photo ...
Thanks for earlier. :)
And I have a 2010 Restayl car, comfort +, manual transmission, unfortunately, what is needed for a cruise? tell me! I understand the whole set + spiral wire? (((
Parad1999
For robot 2007 onwards (there are gearshift paddles behind the wheel) is a spiral wire needed?
no, the spiral is not needed.
For robot 2007 onwards (there are gearshift paddles behind the wheel) is a spiral wire needed?
Hey. as far as I know, you can't. you have a 1.4 engine and there seems to be a different principle of gas pedal control. 1.6 the pedal is electronic, due to this it is possible to control the cruise control. and 1.4 the gas pedal is a cable, but I could be wrong.
Tell me, is the wiring on all trim levels laid or not?
I want to install buttons on the steering wheel: the radio was installed by the previous owner. According to the documents from the radio, there were wires in the set, but if they are not there, now it is difficult to get it.
Done clearly! Only one question: was the wiring for the buttons from the spiral contact to the radio tape recorder already in the car or did he do it himself?
Hey. if you have buttons on the steering wheel or petals under the steering wheel, then don't
And what kind of equipment 17 and 32 mmt? I have a robot. Do I need to buy a spiral? Thank you.
Hey. if the radio is native, then it does not require training. the buttons work immediately.
Yes, they will. I also had a dear one. Since you have a robot with paddle shifters, then you don't need to buy a spiral contact (it is the most expensive), you only take buttons (there are three types of them: 1. radio and bluetooth connection, 2. radio and plug, 3. radio and speed limiter. here
tcorolla-club.ru/fotootch...k-upravleniya-magnitoloj/
tc-club.ru/viewtopic.php?f=42&t=1048
tc-club.ru/viewtopic.php?f=42&t=249 you
will find a lot of interesting
I have a radio tape recorder, but normal without an LCD display, will the buttons work? and I also have a 2008 Corolla MMT. with shift sticks on the steering wheel, I need to buy additional wiring and which one (Spiral contact)
Corolla 11 years old. reystal, the pillow is fastened with springs, there are no bolts. The buttons are connected to the connector but do not work. Someone can put it?
Hey. That is, if I have a Toyota Rav 4 without a multi steering wheel (there is no volume button on the steering wheel, switching tracks), can I install them and they synchronize with the radio without problems? Do you need current buttons and wires themselves?
I also want a multi-wheel) leather steering wheel already have buttons to find)
Hey. There were 3 types of buttons for the Corolla of this model:
1. on the left are the radio buttons, on the right there is a plug (like yours)
2. on the left are the radio buttons, on the right are the phone and speakerphone buttons (like mine) - these were the cheapest
3. on the left are the radio buttons, on the right, the speed limit button and something else.
Yes, I cut off my ears, tk. another pillow cost 15-20 thousand at that time.
I don't see the point of overpaying, so it is possible and a double would only fit. When I bother with this business, there were no duplicates.
The ears were cropped on the pillow, this is because the inserts with buttons were installed, right? I have an automatic transmission with a multifunction steering wheel, but for some reason there are no buttons on the right, can you tell me the functionality? On Ali , the buttons are highlighted, like even in Toyota packaging, does it make sense to overpay for the original?
Hey. I don't remember now. there was a lot of things, and speed limit and speakerphone and whatnot
For the connector that remained "not sewn the sleeve", it turns out that there is a special place (I thought about 15 minutes where to attach it, then it dawned on me - bourgeoisie, eh!), Just inserted into the hole and that's it, but it doesn't connect to anything.
But why don't you know?