Wheel lighting - Toyota Will VS, 2002
Ladies and Gentlemen. Here was born such an idea (or rather peeped) — to make the highlight of the wheels. But since I'm not a specialist in electrics, some difficulties arise. I will state the essence of the idea - the illumination of the wheel from the inside with the help of white and red LEDs. White bring to the near or to a separate button in the salon (to make it more convenient to communicate with gaytsy). Well, red tsepanut on stopari. I think it will look nishtyak — when driving, the wheels are white, and when braking, they are RED! The diodes will be attached to the protection of the brake disc (casing), a small jamb - it will turn out not in a circle, because. there will be a gap due to the support. I don’t see any problems in acquiring diodes, but ... I wanted to ask how to assemble a circuit for outputting a fuse to a button and which one is better, or is it easier not to bother and hook on the neighbor? Actually, that's the whole point. I look forward to approving responses and, accordingly, the development of the idea on your part! If the button accordion does not kick much!
READY! That's actually what happened!
Issue price: 1 500 ₽ Mileage: 77 779 km
Wencel
To powering the light bulb on the ceiling when it is in the door actuation position)
Yes, maybe even easier to the button (which stands in the doorway and is responsible for turning on the ceiling) so it’s easier to pull less wires
To powering the light bulb on the ceiling when it is in the door actuation position)
Wencel
The topic is cool, about the stopars, only you will slow down in front of the gays, they will burn them) You just need a button to activate the backlight.
To do this, power + can be white from the dimensions, red from the stopars, and make the minus a common one, a fuse and a toggle switch in the cabin on it. It remains to correctly position the diodes. the budget will be more than 2 rubles)
but how, and where to connect the backlight under the door, so that it would light up when you open the door ?!
SanekVS
That's the whole point is that I don't want to attract gaborites, so that they don't glow during the day. I still think about the next one.
but how, and where to connect the backlight under the door, so that it would light up when you open the door ?!
Well, that's understandable. I think there will be no problems in choosing diodes, this junk is now in bulk!
I think it is necessary to arrange it so that they are not visible, but only light, diodes also have the direction of light, they do not scatter in a circular manner.
Throwing one wire is not a problem for anyone, for some reason it’s convenient, the diodes consume very little, you can use the neighbor one, I don’t see the difference, but it’s better to put the button, so you have to turn it off, so what? More crap will install them, so that they shine where they need to!
Well, if all the same through the neighbor, will the fuse withstand? Output through the button in the cabin, as I understand it, a bunch of problems.
So if with an activator, as I described, then when the toggle switch is turned off, they will not work, but when you want, they will. Depending on the diodes, you may also need to install resistors.
That's the whole point is that I don't want to attract gaborites, so that they don't glow during the day. I still think about the next one.
The topic is cool, about the stopars, only you will slow down in front of the gays, they will burn them) You just need a button to activate the backlight.
To do this, power + can be white from the dimensions, red from the stopars, and make the minus a common one, a fuse and a toggle switch in the cabin on it. It remains to correctly position the diodes. the budget will be more than 2 rubles)
please find the article, otherwise I didn’t find everything about the sides
, so it’s POSSIBLE
Even as written! Front and sides, you can white and all shades of yellow! I just got caught with green neoncams!
One can argue about the red ones, the rules do not say what kind of light should be on the sides of the car, or am I mistaken?
The idea is excellent, I myself have long wanted to get confused! Everything must be done through the relay, definitely! Reds should not be done, gays will be caught a little will not seem!
Yeah, maybe it will be easier for the girls to negotiate with them, make eyes for them, and for a red light they can be fined 5000 and take them off, like for a special signal!
ahh Beauty, I also want to put it, but it's dangerous, what will happen if the traffic police see it?
They will incriminate something like: "You have this ... that ... it's not allowed ... well, you know yourself ... "))
looks interesting and impressive! And then the illumination of the bottom has already become boring
starlife official
and let's say to the gays: "well ... so ... a sports car, the disks heat up to red, that's how such an effect turns out)))))"
looks beautiful :)
Hahah, the most interesting and reasonable excuse for today is in the comments. Respect)
starlife official
and let's say to the gays: "well ... so ... a sports car, the disks heat up to red, that's how such an effect turns out)))))"
looks beautiful :)
Aha! The pads are new, and they fit in!
and let's say to the gays: "well ... so ... a sports car, the disks heat up to red, that's how such an effect turns out)))))"
looks beautiful :)
no, spectacularly, of course, you can’t say anything, but how will things be in winter? will not close the soldering? Or is she isolated?
The reed switch is a small piece of crap that reacts to a magnet passing by (it is used in many places, in particular in window opening sensors, in security systems). The fact of the matter is that the diodes stand still. But in the simplest case, we break the diode circuit into 4 parts and connect each one through its own reed switch. We place the reed switches evenly around the perimeter of the casing. We stick magnets on the disk. And as the wheel spins, the magnets will turn on the reed switches and the corresponding strings of diodes. And how they will be located depends only on taste and imagination.
Something I did not understand. What are HERGONS? What does it mean - part of the diodes? And my diodes do not rotate (they are attached to the casing (tin) which is behind the brake disc)!
Very beautiful. But when I saw this, I had an idea to modernize your bells and whistles. Apply, no - it's up to you. If you stick 2 magnets on the inside of the disk symmetrically (so as not to unbalance, but attach reed switches to the casing, and connect part of the diodes through them. The diodes will switch along with the rotation of the wheel. Or you can connect it this way to get the effect of rotation in the opposite direction. Even more effective will not be?
TPG
Epoxy doesn't like water.
epoxy glue engine blocks ... and then snot ... the same cold welding has a base - epoxy.
SanekVS
Lord! Do not heat your head, fasten it to a wire or clamps, it will be easier to trick it.
Wow Plastic Clamps theme!
But what about the dirt flying from under the wheels? which strives to penetrate anywhere, well, or snow porridge, for example, it is definitely capable of knocking down such a flimsy structure as a diode tape ... or forcing a snowdrift ... it is also valuable to think about this in advance, before installation.
Lord! Do not heat your head, fasten it to a wire or clamps, it will be easier to trick it.
Mihej
I also wanted to do it for my VAZ-21099 for a long time, I even bought new casings and the LED strips themselves ... Only now the question arose of gluing to, except for the casing - it will fit perfectly on the rear casings (the casing shelf allows you to glue it across the entire width), but for the front the shelf of the casing will be narrowish ... And on what to glue - on the existing adhesive base, it will probably peel off. So I thought to wash off the adhesive base, clean the edges of the casings to the metal and glue them tightly with epoxy ... What do you think?
epoxy from water will turn into snot, better for sealant, and better for glass sealant
KirillBoss
but it seems to me that due to the high temperature, the diodes will melt = / it’s good that winter has begun and it’s cold, but in the heat ...
the diodes are on the casing, not on the brake disc...there is nothing to warm up there...
SanekVS
Well what can I say …
1. I have disc brakes.
2. I did not glue them, but drilled small holes in the casing and fastened them to a thin wire.
3. but I don’t know how to do all this on 09. As far as I remember, there are drum vases on tomosa vases (how are you going to fix them there?)
but it seems to me that due to the high temperature, the diodes will melt = / it’s good that winter has begun and it’s cold, but in the heat ...
yes, yes, they already put rear disc brakes on the basins, many of course are handicraft, but they are also standard, for example, a VAZ 21128 coupe, with a 1.8 engine
Well what can I say …
1. I have disc brakes.
2. I did not glue them, but drilled small holes in the casing and fastened them to a thin wire.
3. but I don’t know how to do all this on 09. As far as I remember, there are drum vases on tomosa vases (how are you going to fix them there?)
I also wanted to do it for my VAZ-21099 for a long time, I even bought new casings and the LED strips themselves ... Only now the question arose of gluing to, except for the casing - it will fit perfectly on the rear casings (the casing shelf allows you to glue it across the entire width), but for the front the shelf of the casing will be narrowish ... And on what to glue - on the existing adhesive base, it will probably peel off. So I thought to wash off the adhesive base, clean the edges of the casings to the metal and glue them tightly with epoxy ... What do you think?
Now I changed the wheels — the casting is not right, it doesn’t look the same as on summer ones, so I don’t often turn it on. Have you seen it for a long time?
Hello. I actually gave myself a green light! Everyone is looking attentively and smiling, and sometimes the Gays are even photographed against the background)))) they are also ... children)))))
The people on the drum brakes can also be put on the current a little confused. If anyone is interested, we can tell you how ...
it was necessary for Astral to poke ANSWER so that he read your comment, otherwise he will not see it if he does not come here again
I don't see it :-) on drums it is placed on two layers of double-sided adhesive tape plus a thermal gun, it is displayed further as you like. They put on the Matrix, satisfied people have been using it for more than 4 months. waiting for winter.
Yes, there is no particular problem. It hasn't reached the critical point yet! Wash Help!
Just a plague! I also want to put it when it will be at least a little warmer) Do they
get dirty very quickly? are the norms washed at the sink?
Do not forget to buy cambric (for insulation) so that you do not bathe with electrical tape.
I immediately put the button, and the backlight is on regardless. So turning the light on and off doesn't matter.
But I’m thinking of putting a separate key in general, so that even without dimensions it shines. So you stand in the dark, and you only see the wheels!
White threw on the fuse of tumanok or dimensions (I don’t remember already), and red from stopars.
Yeah ... but when I was the first in Novosib with such illumination ... Ehhhh ... there was a time ...
Disks, bottom, interior and other things that do not shine in front or back! Can be made in any color! GAI regulates only lighting devices! Stops, turn lights, etc! For highlighting the bottom, wheels, and whatever is highlighted there, they have no right to touch! For example, I explain to them when questions arise! (more often they slow down because of the radiator grille, BUT I have greenery there!))))