What to bring to the weekly trophy? — Toyota Land Cruiser, 4.2 liter, 1997
Last year I was going to the ATL trophy. Several days of competition, several night camps, there is an opportunity for repairs. The question was: what should I take with me? Here is the list
1. Steering rod with tips
2. Spare hoses for power steering
3. Brake pads (front-rear)
4. Right-left front axle shafts — ?
5. CV joints -?
6. Repair kit for steering knuckles
7. Gearbox seals.
8. Cardan crosses (all)
9. Filters (all)
10. Brake hoses and pipes
11. Alternator (just have a spare one)
12. Battery (old, but useful)
13. Tire repair kit
14. Wheel studs with nuts
15. Studs steering knuckles
16. Oil for the engine, gearbox, brake fluid, dextron
17. Autonomous generator + tee extension and low consumption lamp
18. Welding machine — ?
19. Bulgarian
20. GP front — sure!
21. studs + nuts + lock nuts + cones - set
22. Solenoids
23. Fuses are always with you, but you need to check the assortment, a couple of relays, a coil of copper wire
24. Any Toyota fasteners ...
It was for the 80s
This year on land-cruiser.ru, the topic is a similar study for 35 days of off -road
Lubricants, sealants, adhesives:
Motor oil 4l.x4pcs.
Transmission oil 4l.
Dextron 4l.
Antifreeze 0.5l.
Distillant 1l.
Brake fluid 0.3l.
Oil filter (2 pcs.), fuel, air
Heat-resistant grease, tube
MS grease for universal joint, CV joints (2 tubes)
Li grease for bearings (tube)
DonDeal Gray sealant, tube
WD-40 2x150ml.
Poxipol/epoxy
Glue universal
Super-glue
Automatic transmission filter
SST:
Syringe for tube manual
Ball puller with shoulder Three-arm
pullers, stop for KV
Power steering hydraulic cylinder pullers
Oil filter puller Oil
system plugs 2 pcs.
Brake plugs Hub wrench
54 Torque wrench Hose connectors 6-8-10-12-14-16
Wrench 32 for SP-valve Spring ties
Electric and locksmith tools:
A set of professional tools
Taps, lerks
Gas wrench
Gas burner, cylinder
Clamps, a set of
riveters, riveters
Protective glasses, closed
Scrap small, mounting
Welding machine, shield, electrodes
Electric drill + drills 2-12
Bulgarian small. + drive set
Inverter 12-220 2 kW.
Vulcanizer 12V.
Carrying 50m., Wire 1.5kv.
Hacksaw,
Sledgehammer blades
ICE:
Inlet / outlet valves, 1 pc.
Crackers for valves, caps
Timing rollers, timing belt, tensioner fur.
Attachment belts, set
Thermostat block cover
Set of gaskets Turbocharger (oil, coolant)
Brass washers, set
Injector assembly, washers TPA set
Bearings:
power steering tensioner, tensioner, damper
REM-kit for the power steering pump (seal, bearing)
Annular exhaust gaskets 2 pcs.
Starter
Generator
Sensors, EFI:
Boost
SP-valve
crankshaft position
rpm Injection pump
T intake air
coolant EFI
TPS
Correcting resistors injection pump
Starter relay, ECU main, spark plugs 12V
Consumables, hardware:
A set of bolts, nuts, washers, grovers
A set of clips, stoppers, dowels, pins
Rubber seals
Clamps
Sandpaper, set
Knitting wire 1m.
Plastic ties
A set of gaskets for all drains / bays. plugs
Vacuum hose, 1m.
Hoses oil-petrol resistant, set
Electrical:
Multimeter Heat-
shrinkable tubes
Insulating tape abro 3 pcs., safelain 2 pcs.
USB - oscilloscope, 2-channel
Scanner without OS for OBD I, toyo
Wires 1-4kV, meter
Fuses
Terminals
Stripper for wires small.
Soldering iron 12V. solder, acid
Powerful soldering iron 220V
Solder for a radiator, flux (for heating systems)
Interior lamps, headlights, add. lights, turn signals, dimensions, etc.
Transmission:
Wheel bearings 2 pcs., Thrust, locking ring, nut Hub seal
, front
Pivot bearings 2 pcs.
Stocking seals PM, ZM, gearbox shank
A set of gaskets for PM
Silent blocks for clubs, panhard rods Wheel studs
, 2 pcs in front, 2 pcs. 6pcs
Hub Lock Studs, 1pcs Cone Washers
Lower C b and shock absorber washers
, 4 each Nuts: longitudinal rods, panara, steering, SPU
Bolts of cardan, longitudinal rods
Cardan cross
Steering tips 4 pcs, set
Boot of the steering tip 1 pc.
Blocks vkrug , a set of
CV joints?
Brake hoses (pm, pm, body
)
Drain plugs, filler plugs in bridges, RK
Wheels:
Spare tube
Set for repair of tubes, cord
Nipples, caps, nipples
Pneumatics:
Fum-tape
Plug M22 on the receiver, 1/4 on the highway
Chainsaw:
Chain oil 1l.
Gasoline diluted 4-5l.
sharpener, spare chain
saw wrench
band brake
The study is serious, many points will never come to mind, it is useful to discuss
Yes, this is for a large company and several cars. One 5 kW gas generator is able to take half the body of a pickup truck.
Tin ... I will never go on a dzhimnik on such an expedition - even a quarter will not fit)
I liked the list for 35 days, very literate! we took 20 percent of what is indicated there, and sometimes a little more for 11 days.
Well, okay ... The main thing is that the rope from the lebeck is well dragged))
And how funny it was for me when there are two Garmins, I ask the navigator "How much to the point?" but peeps into my Garmin, because his device shows "hell what"
Yes, 276 - one for the navigator, one for me.
And a laptop for developing a strategy for the day and marks in paper maps. It’s just that lately I’ve had navigators who were better guided by other people’s tracks, by pines, moss, the sun, the moon ... but with the OZIK ...
Yes, there was a lot of interesting things on the forum))
Listen, do you have a photo of the salon in the 80s? I have a project here to install office equipment for a navigator, I think where to put the laptop in))
This is all our storehouse of knowledge - a forum on landcruiser.ru
It's just that the original source is always lost, so I put it here. The list that I made for myself was shorter, and completely "drowned" in it.
Except for staples for building a log bridge. They really didn't work for me at all.