Do-it-yourself high-quality soundproofing of wheel arches! — Toyota Camry, 2.4 liter, 2008
Here, finally, the arches rustled according to the new scheme (by the way, I have not yet seen that they make such a noise, they usually make liquid wheel arch liners and glue false Shumka on the locker). I decided to go a little different way. The first step was the removal of the bumper, plastic bumper boot and all lockers. After disassembly, I went to the car wash, thoroughly washed all the arches and the engine. The next step was (the most hemorrhagic and time-consuming) picking out with a screwdriver and a brush with steel bristles, as well as blowing out the remaining dirt in the cups with a compressor from all risers, levers and rods. This is followed by the degreasing of the arches, it is very important to achieve perfect cleanliness in order to subsequently glue the Shumka well. Then I glued everything with false soundproofing (when gluing Shumka, it is necessary to achieve very good gluing without bubbles and gaps between the joints), and then applied liquid fender liner on top! Well, finally degrease the plastic fender liner on the inside and glue it with false soundproofing. Upon completion of all the above manipulations, collect everything that was filmed and leave the car in the garage for one day to dry the mastic. It took two days and 4 sheets of Shumka, 2 or 3 liters of liquid fender liner and 1 liter of degreasing. I am very pleased with the result, it became really quieter! Appreciate and comment.
Dninitrol 479!, super effect. Layer 3 mm. And the noise from the wheels is gone. Just wash the arches well. I have a photo report.
There is an effect! The noise of the wheels that penetrated the interior disappeared!
Soundproofing mastic, it is sold in any auto parts store! I took mine for 300 rubles =-))
Not necessarily, but without it it's easier to rinse everything there. I took it off because a very sticky person on a captiva drove into me before. As a result, I zababahala bumper and headlight. Therefore, I had to remove the bumper, paste the broken headlight, paste a new one (thank God I found it on the cheap from another broken kamryukha) and put everything in place. ). Well, then glue everything. That's something like that! eight))
A very good option! Rear did not think to do so?)
And how to degrease? ordinary solvent, and wipe with a rag? =)
So all the arches are noisy. You need to degrease with an ordinary degreaser, I'm afraid it's not good for paint with a solvent.
Fine. Glad you are doing it yourself. You can see the hands are growing from there. I plan to put Shumko on the whole car in the summer. I took note of your experience.
Hi, have you heard about liquid vibroplast from stp? Very praised, just for such places it will fit :)
I'm afraid to be a necroposter, but: Is
this "like foil" in the photo the mastic for soundproofing the arches?
Another question: in order to perform this action, it is enough to remove the wheel on the jack, remove the mudguards / wheel protection and perform a gluing ceremony on each side? What is the best glue?
Thank you very much for the detailed description!
Can you please tell me if you need a hair dryer? Or can you do without it?
and vibro will not fall off over time? I'm thinking of sticking to the locker or to the body
good job! Did you glue all the arches or only half, what thickness did the vibroplast use?
In your case, maybe not really), I mean the Shumkov of the whole car. There are about 100 kg, if done according to Feng Shui.
All this, of course, is effective, judging by the reviews, but the car will add significantly in weight.
Good job)))
To achieve an even better result — you need to make noise from the motor shield from the passenger compartment.
Under the vibruha there is through corrosion over time. A controversial decision, you need to follow, but nothing is visible ...
correct insulation arches! vibration, and foam rubber or splenitis on top, do NOT work, but work exactly the opposite. Arches need to be made: on a locker - soft material and on iron - hard. Then there will be a sense
There is such a material Nuxodol 3100, it is not expensive, but it is really a high-quality product, unlike all these sticky ones. I advise!
Everyone does it in their own way, but someone applies a little, someone doesn’t apply enough, you just need to glue a lot to have an effect
It is interesting to observe such noise reduction, how the metal will behave in 5-8 years, some flaws will come out over time, or it will be an ideal option for both noise isolation and anticorrosion, because dirt and water will not come into contact with the metal
And I use defender noise, friends from a hundred use it. The price a year ago for Avito was about 500 rubles per 1000 ml. Absolutely easy to apply, the procedure is standard, the car gains a minimum weight, street sounds do not reach the salon, the child falls asleep easily) (but I still have fender liner and door insulation).