A slideshow in games for asus G50vt

zaxarkul
The monitor here at all and. Download АИДУ64 Turn on system monitoring (service->test stability of the system), make all the necessary tick do not start the test and turn your game. After the occurrence of a slideshow look at the evidence charts (Frequency, temperature, voltage, etc.). There will be deviations coincident in time with the slideshow.
And look at the statistics of MSI Afterburner. Maybe the graphics card is where it starts to blunt.

Ryazancev
Thank you! As I will try - I will unsubscribe

Ryazancev
Yesterday tried to do what you suggested, but nothing has understood, moreover, that the CPU was throttling 13%

zaxarkul
Well if the game was throttling, it is very bad. It is necessary to look to the side of the cooling system. M. B. bad pressing of the soles of the radiator (not the twisted cross), bad thermal grease (or spray a thick layer), problems with the speed of the fan, clogged with dust the section of the radiator. Maybe the voltage in the BIOS to lifts -if all previous normal (if at all wattage settings in the BIOS Beech).
We must carefully modify all the parameters in schedules. Can even throw the screens here under the spoiler.

Ryazancev
The voltage settings in the BIOS no. And the rest should recheck. Temperature way for the laptop like normal: graphics: 94 degrees during normal operation, the percent colder as I remember, but in games vidyuhi above 120 is not warming up.

zaxarkul
zaxarkul wrote:
graphics: 94 degrees during normal operation, the percent colder as I remember, but in games vidyuhi above 120 not warmed
For the video chip (GPU), I like on the GTX 780 critical temperature =95 GRS. Celsius. Then the computer goes to reboot. For your 105 (can be up to 120). But it's a shitload, with a temperature map of the long will not live.
In any case you shouldn't be such temperatures. Or burn up the video card, or will a dump of the chip (solder to fall off).
This is not normal and very high temperatures! Until it is better games do not run.Because of this, you and slideshow. Ie the Processor and the graphics card is reaching the temperature limit of the drop frequency, leaving the protection.
You can't check the rotation speed of the cooler to make the cooling system maintenance?

Ryazancev
Understood. Here's a screen test of stability: (a Sharp break in the CPU at the moment of turning off the game)

Spoiler
PS. Forgot to mention that was discovered a trace of the overheating of the chip on a copper-brass (if not mistaken) the gasket, which was expressed by a dark color. Could this be the cause of my problem?

zaxarkul
You have an obvious overheating!
It is desirable to have a direct contact of the chip with a metal base, the thermal pads are much worse in this regard. If they did not, it is necessary to pick up new and the thinner they are the better. You should probably the fat pad, but still old (they eventually deteriorate).
It is better to try to get rid of them completely. Perhaps it is necessary to choose the optimum copper plate thickness and solder it to the base of the radiator (not good at this sorry).
Before you ditch the laptop, I advise you to go in the good service, can that will advise or correct normally your cooling.

Ryazancev
Thank you, hope can solve the problem!

zaxarkul
Accomplish your goal then, Yes.

Ryazancev
Of course, all will describe in detail ;)

Ryazancev
Cleaned up the laptop, changed thermal paste. Now the laptop so fiercely is not overheating, the games run like clockwork, but hot is still far. In games unfortunately the temperature is still high... what video Card to 100 degrees hot, but in older all much better, about 80 degrees. In General, iron is in tatters and therefore, such problems.

zaxarkul
Iron itself from wear temperature increase can not. Only if the Desktop processors under the heat-spreading lid thermal grease dries up (from Intel from 3ххх series 8xxx, AMD have on the old percent).
Something you got wrong with the cooling system, this should not be.

Ryazancev
Don't know what could be. The fan is spinning properly, the laptop is on a cooling stand. May be due to prigarina on the plate or just the cooling system is moronic.

zaxarkul
I would have told you, but I can't see. There should not be thermoregulator for sure!

Ryazancev
They are not there. I'm talking specifically about the very thing copper, which is applied to none.

zaxarkul
Even if you posted a photo of nutriance and process replacement thermopaste or video. Better course to take in normal service, let them see if the tube the heat distribution will change, maybe the thermal paste too thickly applied thermal paste may be bad.

Ryazancev
In short do not in any way deal with the laptop. Heats still strong. Even removed this prigarina :
Spoiler
ie Stoch carefully with an engraver and smeared on chips, thermal paste noctua Nt-h1 (4.5 W/MK), nothing has changed. Today tested it and miraculously the temperature was about 85 degrees, but later in the same magical way, they begin to grow exponentially. Cooling pad all the way does not help.

zaxarkul
In copper telotroch is a liquid, when heated, it boils, it evaporates and condenseries. Perhaps it faded with time from the defect of the heat pipes. Or maybe the contact of the sole with teletrapami bad (there solders usually, can fell).
Take in normal Service let look. But the penetration looks like the pads appeared, this thermal grease doesn't usually leave.

Ryazancev
I'm told that the pads were not! There was bad thermal paste, it probably had a lot of problems (artifacts on the monitor, etc.), but it was still early, before I needed this comp to recover so to speak. And what about liquid perhaps it should be clarified in the service center. I think soon all poprosy will finally disappear and I'm going to get rid of this problem.