RX588 temperature

Denis Kyokushin
I have not tried to turn on the turntables in MSI Afterburner so that they do not stop, that is, they will spin at different speeds only they will not stop, but it cools more effectively so the temperature gets lower.

Denis Kyokushin
1 ..... re-soldering of the memory chip 2 is possible .... re-soldering of the graphics chip 3 ... the thermal relay is not in order 4 .... when changing the thermal paste by unscrewing and screwing in the backplAit it could damage the thyristor (resistor) of temperatures responsible for stability

And what's the problem? Gnilobaytovsky rubbish is about this pace and should have + it's summer now)

Listoman
Here is the same map, only in the early stages of the test:
Spoiler
Not even 70 °. But The Witcher 3 warmed up.
Listoman wrote
Gnilobaytovsky trash about this pace and should have
Sometimes even worse, the same Asus Dual, his default speed is not higher than 2000 in minutu.Nuzhno reflash the BIOS if you wish at least to 2400 revolutions raise
Listoman wrote:
+ it's summer )
Who has summer, and who has cool May. I wonder if the change of season affects so much, then why are there no such temperature jumps on the old HD7950 as on the Giga in comparison with its test on December 1?

KENIG_39
How did I overheat if the card is running in the drain?
KENIG_39 wrote:
4 .... changed when screwing and unscrewing thermopaste bEkplEyt could damage tirister (rezister) responsible for temperature stability
in the header threads video Witcher 3 without vskrytiya.Chitay carefully

Tekeshi_Tetsuo
In Byunere schedule included so that at 70 ° turntable spinning at 100% .In the video "cooler gpu" shows the rpm of the turntables

Denis Kyokushin
So I will write again, since the last comment was deleted for some reason, in short, all the same, the thermo gaskets need to be changed.

Summer has come, do the limitation of personnel.
Try Death Stranding, it shouldn't get warm. If it doesn't get warm, then the problem is in the game The Witcher 3 + outrageous settings. There are unoptimized games that fry the card even on the menu.

Tekeshi_Tetsuo
They are new. Thickness 0.5 mm. At first I ordered 1mm, but they turned out to be hard, and the radiator did not reach the chip. I caught a black screen and wild noise of valves. I turned off and pulled out the card. Thermal pads are an expensive pleasure. I already threw 3 pieces on them. experimenting

Denis Kyokushin
In short, you need to look for those that fit, in a word, hemorrhoids.

Denis Kyokushin Thermal
pads 0.5mm, after all, they are suitable for these memory chips, you don't need to thinner. I'm certainly not a specialist, but as far as I know, they need to be cut to the size of the chip, and not put in sausage ... And I don't know how much it matters, but the thermal pad does not lie in this place from the factory.


But for the feeding phase, others are usually used. Presumably, a "thermo-gum" will do, that is, something softer. Used on chokes (1.23mm), mosfets (1.23mm) and under backplate (1.30mm), you can round up and put 1.5mm on everything. Well, maybe you can try 2mm on mosfets.
If it suddenly happened that the factory thermal pads that were on during the power phase remained intact, I think it makes sense to try to put them back in place.

Perhaps the reason for such temperatures lies in the nuances listed.

Marsj
Can still launch kc 1.6? Or do you think Furmark is a problematic program, because the video card is 100% loaded?
No need to balabol, if you do not understand and there is no desire to help figure it out, shut up, they will consider it smart.

IngwardIn
I wrote a working solution to the problem, not overclocker's tips for on-screen numbers.
100% load without frame limitation - increase in power consumption of the card - increase in temperature.
Maybe someone also likes to heat the processors to 100 degrees and burn electricity.

Marsj
Your decision is not to use the full potential of the video card and play other games. Well a genius.
Based on your logic, if percent. will heat up above normal, then the PC just needs not to be turned on. I never cease to be amazed at your ingenious advice, in almost every subject where you do not understand, but want to insert 5 kopecks.
For that matter, instead of limiting personnel, you can do undervolting, but in this situation, such advice is not appropriate.

Denis Kyokushin
My RX590 also warmed up a little, slightly reduced the voltage through the card drivers and adjusted the fan rotation curve, now the temperatures under heavy loads are 65-70.

I had a video card disassembled, thermal pads and paste replaced everything, put everything together, launched temperature tests for 80 grams. the revolutions of the turntables for 4000, the result is deplorable. The service said that this is the norm, but if you want to do something yourself, then do not be afraid, you can even reflash the BIOS if the video card bends, then we will send it to the center, they will figure it out. Once again I disassembled all the thermal pads, I did not like the trace of thermal paste on the chip, I decided to reduce the thickness of the thermal pads on the memory from 1 mm. by 0.5 mm. ... I started assembling with a check, glued small pieces of thermal pad just for memory and very thin drops of thermal paste on the chip in the center and in the corners, assembled the heatsink to the board without tightening the screws, just pressed it on top, again removed the drops of thermal paste smeared. On the rest of the places I glued the softest thermal pads available, 1.5 mm. hoping that they will be sold during assembly and will not interfere with the contact of the heatsink with the chip. It took about 5 thousand rubles for experiments. Collected, the BIOS of the video card flashed in the result, everything is normal - the temperature dropped to max. from 84 to 76 degrees turntable revolutions from 4000 to 2200 max. Periodically I check it no more. The left shot before disassembly is the right one.

AnPei
What thermal pads did you use? What thermal conductivity?

semferot48
I did an undervolting, I didn't get any steep drops in temperature. This is still somewhere in the last year. True, I don't remember whether there were crashes or a black screen

IngwardIn
IngwardIn wrote:
And I don't know how much it matters, but in this place from the factory the thermal pad does not lie
Absolutely correct
Spoiler The
factory thermal spacers were about 1 mm thick, but soft. I ordered the same thickness, they turned out to be denser:

As a result, the radiator did not reach the chip, and the TV set caught a black screen, and the valves began to make noise
Again, you have to disassemble.
I have one thought to create such a "collective farm":
Spoiler

As soon as I have free time, I will test it and post it

Denis Kyokushin
I installed 1.0 mm thermal pad arctic memory chips for the first time. the rest of the thermal pad pro lecend 1.5 mm turned out to be complete garbage, nothing has changed. For the second time on chips thermal pad arctic 0.5 mm for the rest gelid gp-extreme 1.5 mm. , thermal grizlly kryonaut thermal grease and the video card worked as it should.

AnPei
And what is meant by the word "chips"? Memory banks?

Kyokushin Denis
Denis Kyokushin wrote:
I did andervolting, some steep temperature gradients poluchil.Eto not somewhere else in the past godu.Pravda, I do not remember, or crashes, or black screen shlopotal
If you do everything correctly (provided that with the cooling system itself, everything is in order), then the result should be very noticeable, of course, if you did not expect a decrease in temperatures by 2 times.
Denis Kyokushin wrote:
I have one idea to make such a "collective farm"
before going on a collective farm, first try to choose the right thickness of thermal pads. This can be done using ordinary plasticine (or old gaskets, if they are in good enough condition for measurements): put a small ball of plasticine in those places where the thermal pads should be; screw the CO, how it should stand in order to "flatten" the plasticine, then carefully disassemble the card and measure its thickness, and then buy the thermal interface by the thickness closest to the required size (you should not take it with a large margin, even if the gaskets are soft)

Denis Kyokushin
Around the crystal there are memory chips or banks, the name of the essence does not change.

Denis Kyokushin wrote:
Again have to disassemble.
I have one idea to create such a "collective farm":
Denis Kyokushin
I think that there is no need to work on a collective farm , I think that a little change in the installation of thermal pads and choose suitable thermal pads, or install old ones for BPM and that will be enough.

I propose to navigate here on this video, although the video card is different, but the diagrams are the same, and the person is engaged in the repair of video cards.

Or now, replacing thermal pads on the same card.