Overheating 8320
Actually there was a problem, the percentage heats up to 75 and resets the frequency. Cooler Master V8 GTS cooler I don't think that the processor should be so hot, given that there were no such problems before. There is no dust either - absolutely, recently the kit has moved to a new building.
TheDisgusting
then it’s sad, look, but there is another question - in the factory installation near the processor there are 2 plastic plates, did you even remove them (they are attached to the bottom plate)? Or are you hooked on them?
TheDisgusting
any market store where used components are sold, there are a lot of these mounts, they are almost all the same
. Plus, it was very difficult to disconnect the cooler from the processor, and the paste itself turned black.
It’s better to shoot from a warm process and carefully with your feet, but why is the paste dark, what is it called?
Shadows3D I
removed them, only the plate behind the mother, which, roughly speaking, was installed from the cooler according to the instructions, but what was strange was that my cooler did not stand up on large mounts, they did not fit into the grooves, so I put them vertically on the small ones.
And yes, I already called 2 service centers, they say there are no fasteners.
iMolodec
Pasta that came with a cooler. There is no exact name, but yes, I shot it with about a 30 degree processor.
It seems the problem is being solved, I found a representative of the company in Moscow from the official website of Cooler Mastera, it seems like they send consumables, I dropped them an email. I also found a person with the same cooler, to whom they already sent the screws, so they should help.
Oh lord! This is just an example of how not to arrange air exchange in the case!
Here everyone has already chewed a little, but the mistakes made by a person in short
1. Blowing from the top is a disgrace! hot air rises and instead of being blown out, it is diluted. Not the best solution. The fans at the top of the case should BLOW, decorative blinds do not interfere much with this, the grille has much more resistance.
2. The processor fan blows into the case - the same is original, but the air is immediately blown back, because a 120mm spinner drags it out of the case. - As a result, the CPU cooler is surrounded by hot air. (although in this case, the person even managed to put it on the air intake =)
3. The power supply sucks warm air from the video card, while a grate is visible in the bottom of the case, especially for the power supply to take in cold outside air. and did not suck through the dust in the entire corps. Usually, a filter is also provided for the power supply in such cases. It is through such a grille that air must enter the power supply. He is not sickly heated, and you still want to warm him up
4. General advice.
in such cases, as a rule, there is a place for installing the fan (s) on the front panel and on the bottom of the case, in this case, the holes in the bottom of the case are also covered with filters!
What does this say? And about the fact that it is necessary to install the most productive fans there! And they should work on blowing air into the body.
If the intake air passes more through the filters, then less dust will accumulate in the housing! Less dust - your supercoolers for 5000 will work, and not be clogged in three days with a dusty mattress of such density that you can use it instead of insoles or caulk windows!
Even on the side walls, opposite the video card, you can hang fans for blowing, and glue them on the outside with self-existing filters.
Just don't forget to vacuum the bottom filters once a week =)
TheDisgusting
Full cast - this means that your cooler is adjacent to the heat-distributing cover of the processor.
And this is good.
Convex casts indicate poor quality processing of the sole of the cooler. But I have not heard about convex or concave cooler soles and heat-distributing covers for a long time. That used to be a problem! especially stubborn overlockers polished them with GOI paste on glass, or even rubbed them to processor covers like car valves in landing slots =)
SUSUL1
The problem now rests on the power supply unit, you will have to cut a hole in the case, otherwise the fan will be covered with metal.
And so I'll know, the mounts will come, I'll assemble it, take a photo, I didn't have such coolers, I had a Phenom 955 with an ordinary tower cooler (something like a boxed one).
Regarding the mounts, the representatives themselves refused to help - you lost, your problems, the case is not guaranteed - good luck with your search, but just on the forum I found a person who also unsubscribed (I was looking for mounts for Intel), so he helped me out, sent me yesterday my irons.
It remains to collect normally all these pieces of iron
TheDisgusting
I don't quite understand what power supply cutout we are talking about?! Your whole bottom is full of holes, in filters and louvres. The power supply unit sucks in outside air
Well guys, did you get it right? Of the minuses, it was not possible to connect the front 3.0 usb and the front audio outputs, since they are not conveniently soldered + removed the top fan of the case, because the whole thing did not fit because of
the 
cooler
adapter think okay? And then again they started telling me that with such a cooler there should be less