Performance issues (Cyberpunk 2077)
I downloaded a fresh cyberpunk, the license naturally, initially understood that the game is demanding and on high I will not play, but low-medium already had to workCharacteristics:
Radeon Rx580 8gb
Rizen 3 1300x 3.5gggz
16GB of zoose
Of course, I understand that the specks are not the best, but not a weak PC I have, though a narrow neck in the form of a quote creates problems.
And so I start the game and... 15 phps on recommended (high), put low and... 15 phps... it is very strange and I think that the problem is not in the power of my PC, but then what? Optimization? why do I have the same phps on high and low? Maybe someone has something like that. Help, tell me.
Supplement the post
"Playing" a little noticed that not a percent of not a vidyyuk do not load 100 percent or close to it somewhere at 50-60 and that and what might be the cause?
R5 3600 stock + rtx 2060 + 32GB 3200 RAM.Everything except fog is at maximum, rtx is off, DLSS for quality, from 40 to 57 fps depending on the terrain, in the extension 3440 to 1440
there is a fix for ryazhenka threads and a dll memory management config is fixed ...
who would not say anything here, but the game needs a very powerful percentage. even if in monitoring your percent is loaded by 50% and the card is not 99 but 98-97, this already means an emphasis either in percent or in the memory subsystem !! the game has a bunch of geometry that is processed by the percent.
jaconda123 wrote:
dll memory management config
This file is a rudiment that does not work, I quote from the developers
Removed the memory_pool_budgets.csv file. which was not connected with the final version of the game and had no influence on it (it was a leftover file used during the development to estimate memory usage. It had no effect on how much memory was actually allocated). Perceived performance increase after editing the file may have been related to restarting the game.
Well, you have a good 2060, which shows the same result as a super 2070 :) Or did you measure the FPS in the main character's apartment? :)
worys
It still works somehow. I checked it on version 1.04, on the same save, 16 gigs of memory, with the default settings the game takes about 7.5, if you put PoolCPU 8 gigs - the same, if you put 12 - it takes 8.5. Video card 2 giga, if you leave it by default (3) - the memory is loaded in full, if you put 2 - 1.7 is loaded.
Nukemall
Yes, yes, the file with the game is not connected in any way, but it works for you (in the update that will soon be released it will not be), and 2060 is like 2070 super :)
Denis Kyokushin
it makes no sense to change thermal paste without scalping and new thermal pads
Denis Kyokushin
if it's dry on the radiator then under the lid you think everything is damp? the temperature will not be greatly reduced without replacing the paste, somewhere 3 degrees will drop the maximum, just like with processors who have more than 2-5 years of percent or vidyaha, then under the lid there is gum and not paste
Pgokda
I heard that the new cards have chewing gum. In general, as it were, I'm writing about replacing the paste. If you replace it, then there is a sense
Good day. Faced the same problem as at the beginning of the discussion. And that is, with absolutely any settings, my FPS does not rise above 20 but also does not fall below 10, on average, it keeps at 13-17. I collected the PC recently. About 2 months ago. Features rx 5700 xt, ryzen 7 2600 pro, 16 GB RAM and SSD for games samsung m.2 970 evo.
The drivers have been updated and, just in case, even some have been removed and reinstalled on a clean one. It did not help. 2 monics are connected to the PC. I tried to disable one and work with only one. Did not help.
With all this, percent and vidyuha work somewhere at 20-30% for a few seconds, the load can rise to 60-70%. The RAM eats about 8 GB and the video memory is about 5 GB.
Who knows what the problem is? Is the problem in the hardware or is it in the game?
Andrei1505 the
problem is in the driver on Vidyahu ... there you MUST disable all kinds of optimizations from the manufacturer.
Roughly speaking, make the video work with the driver, without any options from the driver.
On my 580th, on the second computer, it was also like this - I installed the 19th firewood, which was the last, before the complete update of the driver control panel interface ... And Voila)) There, by default, all these pribluda with optimizations are Disabled. But it's better to check just in case.
Ryzen 5 3600
Nvidia 1660 super
16 GB RAM 3200
ssd m2 samsung evo 970
mother on b450
Guys like this: I installed cyberpunk on the incentive, installed it on a ten-year-old hard drive, everything worked fine at an impressive quality of ~ 60 fps. I installed a new m2, put Windows on it, and installed cyberpunk, as a result of -20 fps. What could be the problem and how to fix it?
I9 10900K
NVIDIA RTX 3090 SUPER
32 GB RAM 4000
SSD M2 SAMSUNG EVO 970
MB MSI MPG Z490 GAMING PLUS
Graphics: Ultra + RTX Graphics
FPS = 120 ~
guys, with the config - i9 11900k 3090 32 gb 3600, on ultras in 4k sometimes drawdowns up to 33 fps. I look at the boys' reviews 40 - 45 fps. What can be wrong ?
If you do not enable tracing, then you can play at impressive graphics settings without problems.
Config for weak PCs - for new players so as not to knock around the entire forum
i7-860 SSE 4.2
8GB
GTX 980 4Gb
source
https://forums.playground.ru/cyberpunk_2077/tech/vylety_na_windows_7-1000347/
Regarding the performance of the game, I can say that it clearly remains with an eye on video cards of future generations