Overclocking is all about overclocking v.6

Vinni-Pukh
For six and eight core processors of Intel (because this technology is only for 2 processors and provided) with a base frequency of 3.0-3.2 GHz tehnologie this really might be a good crutch, certainly not know how it will work in fact, because monopolism segobia and FX-60 on ur right, and the CPU is never free completely.
AMD and other Intel processors like the bullshit until you have to, because they are so frequency is high.
But the automatic overclocking of the CPU temperature on the ceiling - this is really cool! Here is a review of the work of this technology is to wait=)

SUSUL1
SUSUL1 wrote:
But the automatic overclocking of the CPU temperature on the ceiling - this is really cool!
The usual nonsense, like automatic overclocking on the Mat Board. Choose autorange, Mat Board asks what I have, box, tower, or water, in the first case, the processor accelerates to 4000 MHz, in the second to 4200, and 4300 in the third. Although the step in the voltage can be so small that it can ask for water, and not the tower, but the tower is quite and above to cope.

Vinni-Pukh
The garbage that auto overclocking. +10% max. The voltage it puts immediately the maximum permissible
And I have the cooler allows to drive the CPU to 4.7 GHz, but the mother Board starts yelling about overclocking and run dual start already at 4.2 GHz

SUSUL1
Well, maybe your cooler only allows you to drive a good crystal, not average scall
the mother Board starts yelling about overclocking and run dual start already at 4.2 GHz
There probably is not enough of a secondary voltage

Vinni-Pukh
Yes, that's the same thought, but brodigan multiplier, chipset do not touch, memory is not the same touch...
And on the forum, many complain of a double start Gigabaytami motherboard.
And support them - would be better if it was not

and that really is my percent not how to overclock ? anyone knows

CLOCK WATCHDOG TIMEOUT - because of what you may receive?
Tried to overclock 4790k to 4.4 Ghz at 1.290 vcore and vrin 1.900
Mat. Board B85-HD3

Nikita237
Nikita237 wrote:
CLOCK WATCHDOG TIMEOUT - because of what you may receive?
Tried to overclock 4790k to 4.4 Ghz at 1.290 vcore and vrin 1.900
Mat. Board B85-HD3
10? Go to event viewer, the code itself BSOD.
x101 or x124
And so, much stress for 1,290 and small IVR

Vinni-Pukh
Yes, x101

Nikita237
Not enough Vcore, I need to improve.
Pick up the first Input Voltage up to 2,000 or 2,100
Dam of Calla lilies of course

Vinni-Pukh
Above 1.900 does not raise

Nikita237
then increase VCore, or lower to 4.3 GHz and have to be measured
Dam Callas ( no offense ). A lifting power controller (input voltage) up to 2,000-2,100 good allows you to understate the VCore

Vinni-Pukh
I read an article from asososca specialists, they do not recommend input 1.95 and above... and just input needs to be ~ +400-600 mV from the voltage of the stone.

WWQ
Again, this is a recommendation for E processors and socket 2011 and 1150 can be raised up to 2.3

Vinni-Pukh
There are 1.9 sounds scary... but the 2.3 I don't know :-P

WWQ
Sadly 4790@4400 at 1.29 v does not hold, I'd think they'd have a little better appetite, my 4770 too, on top of the games ran @4400 at 1.29 v, then I had VIDOS to encode and bsdos was up until stability is found at 1.33 v and the bottom Input Voltage 2.0 for a good motherboard is garbage.

DozoRRR
DozoRRR wrote:
Sadly 4790@4400 at 1.29 v does not hold, I thought they were a little better with an appetite
He has a lousy mother, what is there to be surprised ?

4670K@4500 without raising voltage easy ICE HAMMER 4800 with two TY 140